adate302-02 Analog Devices, Inc., adate302-02 Datasheet - Page 4

• Manufacturer Part Number: adate302-02
• Description: 500 Mhz Dual Integrated Dcl With Differential Drive/receive, Level Setting Dacs, And Per Pin Pmu
• Manufacturer: Analog Devices, Inc.

ADATE302-02
SPECIFICATIONS
V
defined in Table 37. All specified values are at T
Temperature coefficients are measured at T
analyses, and/or limited bench evaluations. Typical values are not tested or guaranteed. Test levels are specified in the Explanation of Test
Levels section.
TOTAL FUNCTION
Table 1.
Parameter
TOTAL FUNCTION
POWER SUPPLIES
TEMPERATURE MONITORS
VREF INPUT
DD
Output Leakage Current
Output Capacitance
DUT Pin Range
Total Supply Range, V
VPLUS Supply, V
Positive Supply, V
Negative Supply, V
Logic Supply, V
Comparator Termination, V
V
V
Logic Supply Current, I
Comparator Termination Current,
Positive Supply Current, I
Negative Supply Current, I
Total Power Dissipation
Temperature Sensor Gain
Temperature Sensor Accuracy Without
Reference Input Voltage Range for
Input Bias Current
PLUS
PLUS
= 10.0 V, V
PE Disable, Range E
PE Disable, Range A, B, C, D
High-Z Mode
I
Calibration over 25°C to 100°C
DACs (VREF Pin)
COMP_VTTx
Supply Current, I
Supply Current, I
CC
CC
PLUS
= 3.3 V, V
DD
SS
PLUS
PLUS
PLUS
CC
DD
to V
SS
COMP_VTTx
SS
SS
= −5.75 V, V
Min
−20.0
−400
−2.0
16.25
9.5
−6.0
3.1
1
−1.0
4.0
1.0
40.0
140.0
170.0
200.0
230.0
2.5
3.0
4.95
PLUS
J
= 80°C ± 20°C, unless otherwise noted. Typical values are based on design, simulation
= 16.75 V, V
J
= 80°C, where T
Typ
+6.0
7.5
+15
4
22.5
16.75
10.0
−5.75
3.3
1.5
+1.3
12.7
2.7
46
190
231
272
311
3.55
4.2
10
6
5
0.08
Max
+20.0
+400
+6.0
23.25
17.25
10.5
−5.5
3.5
3.3
+4.0
17.0
10.0
70.0
256.0
311.0
406.0
461.0
4.0
5.5
5.05
100
COMP_VTTx
Rev. 0 | Page 4 of 52
J
corresponds to the internal temperature sensor, unless otherwise noted.
Unit
nA
nA
nA
pF
V
V
V
V
V
V
V
mA
mA
mA
mA
mA
mA
mA
mA
W
W
mV/K
°C
V
μA
= 1.5 V, V
Test
Level
P
C
P
S
D
D
D
D
D
D
D
P
P
P
P
P
P
P
P
P
P
C
C
D
P
T
T
T
REF
= 5.0 V, V
−2.0 V < V
Defines PSRR conditions
Conditions/Comments
VCH = 7.0 V, VCL = −2.5 V
−2.0 V < V
VCH = 7.0 V, VCL = −2.5 V
−2.0 V < V
SPI; RCVx pins active, VCH = 7.0 V, VCL = −2.5V
VTERM mode operation
Defines PSRR conditions
Defines PSRR conditions
Defines PSRR conditions
Defines PSRR conditions
HVOUT disabled
HVOUT enabled, RCVx pins active, no load, VHH = 12 V
Quiescent (SPI is static)
Load power down (IOH = IOL = 0 mA)
Load active off (IOH = IOL = 12 mA)
Load power down (IOH = IOL = 0 mA)
Load active off (IOH = IOL = 12 mA)
Load power down (IOH = IOL = 0 mA)
Load active off (IOH = IOL = 12 mA)
Temperature voltage available on Pin A1 at all times and
on Pin K1 when selected (see Table 24 and Table 36)
Referenced to V
Tested with 5 V applied
REF_GND
DUTx
DUTx
DUTx
< +6.0 V; PMU and PE disabled via SPI;
< +6.0 V; PMU and PE disabled via SPI;
< +6.0 V; PMU disabled and PE enabled via
REF_GND
= 0.0 V. All default test conditions are as
; not referenced to V
DUTGND