SST49LF016C-66-4C-NHE SST [Silicon Storage Technology, Inc], SST49LF016C-66-4C-NHE Datasheet - Page 16
![no-image](/images/no-image-200.jpg)
SST49LF016C-66-4C-NHE
Manufacturer Part Number
SST49LF016C-66-4C-NHE
Description
16 Mbit LPC Serial Flash
Manufacturer
SST [Silicon Storage Technology, Inc]
Datasheet
1.SST49LF016C-66-4C-NHE.pdf
(37 pages)
Data Sheet
DEVICE COMMANDS
Device operation is controlled by commands written to the
Command User Interface (CUI). Execution of a specific
command is handled by internal functions after a CUI
receives and processes the command. After power-up or a
TABLE 8: Software Command Sequence
©2006 Silicon Storage Technology, Inc.
Command
Read-Array/Reset
Read-Software-ID
Read-Security-ID
Read-Status-Register
Clear-Status-Register
Sector-Erase
Block-Erase
Program
Program-/Erase-Suspend
Program-/Erase-Resume
User-Security-ID-Program
User-Security-ID-Program-Lockout
10. WA = Address of memory location to be written
11. WD = Data to be written at location WA
12. Valid addresses for the User Security ID space are from FFFC 0188H to FFFC 019FH.
1. This value must be a valid address within the device Memory Address Space. X can be V
2. SST Manufacturer’s ID = BFH, is read with A
3. Following the Read-Software-ID/Read-Security-ID command, Read operations access manufacturer’s ID and Device ID or Security
4. IA = Device Identification Address/Security ID Address.
5. ID = Data read from identifier codes/Data read from Security ID
6. SRD = Data read from Status register
7. The sector or block must not be write-locked when attempting Erase or Program operations.
8. SA
9. The Program command operates on multiple bytes.
SST49LF016C Device ID = 5CH, is read with A
Following the Read-Software-ID/Read-Security-ID command,
Read operations access Manufacturer’s ID and Device ID or Security ID.
ID. Read-Software-ID/Read-Security-ID and Read-Status-Register will return register data until another valid command is written.
Attempts to issue an Erase or Program command to a write-locked sector/block will fail.
BA
X
X
7
for Sector-Erase Address
for Block-Erase Address
,
9
7
7
3
2
/
3
12
Bus Cycles
20
Required
-A
20
≥ 2
0
-A
1
2
1
2
2
2
1
1
2
2
= 0.
1
= 0, A
0
= 1.
16
Oper
Write
Write
Write
Write
Write
Write
Write
Write
Write
Write
Write
Reset operation the device enters Read mode. Commands
consist of one or two sequential Bus-Write operations. The
commands are summarized in Table 8, “Software Com-
mand Sequence”.
First Bus Cycle
Addr
X
X
X
X
X
X
X
X
X
X
X
1
IH
Data
D0H
FFH
B0H
A5H
90H
70H
50H
30H
20H
40H
10H
85H
or
or V
16 Mbit LPC Serial Flash
IL,
but no other value.
Read
Read
Oper
Write
Write
Write
Write
Write
Second Bus Cycle
SST49LF016C
Addr
WA
WA
SAx
S71237-07-000
BAx
IA
X
X
4
10
10
8
1
SRD
WD
Data
Data
D0H
D0H
00H
T8.0 1237
ID
5
11
6
9/06