ST72325 STMICROELECTRONICS [STMicroelectronics], ST72325 Datasheet - Page 126
ST72325
Manufacturer Part Number
ST72325
Description
8-BIT MCU WITH 16 TO 60K FLASH/ROM, ADC, CSS, FIVE TIMERS, SPI, SCI, I2C INTERFACE
Manufacturer
STMICROELECTRONICS [STMicroelectronics]
Datasheet
1.ST72325.pdf
(193 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 126 of 193
- Download datasheet (2Mb)
ST72325
I
10.7.7 Register Description
I
Read / Write
Reset Value: 0000 0000 (00h)
Bit 7:6 = Reserved. Forced to 0 by hardware.
Bit 5 = PE Peripheral enable.
This bit is set and cleared by software.
0: Peripheral disabled
1: Master/Slave capability
Notes:
– When PE=0, all the bits of the CR register and
– When PE=1, the corresponding I/O pins are se-
– To enable the I
Bit 4 = ENGC Enable General Call.
This bit is set and cleared by software. It is also
cleared by hardware when the interface is disa-
bled (PE=0). The 00h General Call address is ac-
knowledged (01h ignored).
0: General Call disabled
1: General Call enabled
Note: In accordance with the I2C standard, when
GCAL addressing is enabled, an I2C slave can
only receive data. It will not transmit data to the
master.
Bit 3 = START Generation of a Start condition.
This bit is set and cleared by software. It is also
cleared by hardware when the interface is disa-
bled (PE=0) or when the Start condition is sent
(with interrupt generation if ITE=1).
– In master mode:
126/193
2
2
C BUS INTERFACE (Cont’d)
C CONTROL REGISTER (CR)
the SR register except the Stop bit are reset. All
outputs are released while PE=0
lected by hardware as alternate functions.
TWICE with PE=1 as the first write only activates
the interface (only PE is set).
0: No start generation
1: Repeated start generation
7
0
0
PE
2
C interface, write the CR register
ENGC START ACK
STOP
ITE
0
– In slave mode:
Bit 2 = ACK Acknowledge enable.
This bit is set and cleared by software. It is also
cleared by hardware when the interface is disa-
bled (PE=0).
0: No acknowledge returned
1: Acknowledge returned after an address byte or
Bit 1 = STOP Generation of a Stop condition.
This bit is set and cleared by software. It is also
cleared by hardware in master mode. Note: This
bit is not cleared when the interface is disabled
(PE=0).
– In master mode:
– In slave mode:
Bit 0 = ITE Interrupt enable.
This bit is set and cleared by software and cleared
by hardware when the interface is disabled
(PE=0).
0: Interrupts disabled
1: Interrupts enabled
Refer to
events and the interrupt.
SCL is held low when the ADD10, SB, BTF or
ADSL flags or an EV6 event (See
tected.
0: No start generation
1: Start generation when the bus is free
0: No stop generation
1: Stop generation after the current byte transfer
or after the current Start condition is sent. The
STOP bit is cleared by hardware when the Stop
condition is sent.
0: No stop generation
1: Release the SCL and SDA lines after the cur-
rent byte transfer (BTF=1). In this mode the
STOP bit has to be cleared by software.
a data byte is received
Figure 70
for the relationship between the
Figure
69) is de-
Related parts for ST72325
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
THYRISTORS
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
ADJUSTABLE INVERTING NEGATIVE OUTPUT CURRENT MODE PWM REGULATORS
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
0.25A SCRs
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
0.8A SCRs
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
Smartcard MCU With 4 additional I/0
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
SERIAL 2K (256 x 8) EEPROM
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
Search -----> STP10NB50FP
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
Search ---> STP12NB30
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
Search -----> STP13NK50Z
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
(MSS40 / MSS50) BACK TO BACK SCR MODULE
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
Dmos Programmable High Speed Unipolar Stepper Motor Driver
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
LOW Votage Telephone Speech Circuit
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
Technical Article
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
Thyristormodule
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
SCR
Manufacturer:
ST Microelectronics
Datasheet: