ST10F271E STMICROELECTRONICS [STMicroelectronics], ST10F271E Datasheet - Page 45
ST10F271E
Manufacturer Part Number
ST10F271E
Description
16-bit MCU with 128 Kbyte Flash memory and 8/12 Kbyte RAM
Manufacturer
STMICROELECTRONICS [STMicroelectronics]
Datasheet
1.ST10F271E.pdf
(180 pages)
- Current page: 45 of 180
- Download datasheet (2Mb)
ST10F271B/ST10F271E
6
6.1
6.2
Bootstrap loader
ST10F271 implements Boot capabilities in order to:
●
●
Selection among user-code, standard or selective bootstrap
The boot modes are triggered with a special combination set on Port0L[5...4]. Those
signals, as other configuration signals, are latched on the rising edge of RSTIN pin.
●
●
●
Table 25.
Standard bootstrap loader
After entering the standard BSL mode and the respective initialization, the ST10F271 scans
the RxD0 line and the CAN1_RxD line to receive either a valid dominant bit from CAN
interface, or a start condition from UART line.
Start condition on UART RxD: ST10F271 starts standard bootstrap loader. This bootstrap
loader is identical to other ST10 devices (example: ST10F269, ST10F168).
Valid dominant bit on CAN1 RxD: ST10F271 start bootstrapping via CAN1.
.
P0.5
1
1
0
0
Support bootstrap via UART or bootstrap via CAN for the standard bootstrap.
Support a Selective Bootstrap Loader, to manage the bootstrap sequence in a different
way.
Decoding of reset configuration (P0L.5 = 1, P0L.4 = 1) will select the normal mode
(also called User Mode) and select the user Flash to be mapped from address
00’0000h.
Decoding of reset configuration (P0L.5 = 1, P0L.4 = 0) will select ST10 standard
bootstrap mode (Test-Flash is active and overlaps user Flash for code fetches from
address 00'0000h; user Flash is active and available for read accesses).
Decoding of reset configuration (P0L.5 = 0, P0L.4 = 1) will activate new verifications to
select which bootstrap software to execute:
–
–
if the User mode signature in the User Flash is programmed correctly, then a
software reset sequence is selected and the User code is executed;
if the User mode signature is not programmed correctly in the user Flash, then the
User key location is read again. Its value will determine which communication
channel will be enabled for bootstraping
P0.4
ST10F271 boot mode selection
1
0
1
0
User Mode: user Flash mapped at 00’0000h
Standard Bootstrap Loader: User Flash mapped from 00’0000h, code fetches
redirected to Test-Flash at 00’0000h
Selective Boot Mode: User Flash mapped from 00’0000h, code fetches
redirected to Test-Flash at 00’0000h (different sequence execution in respect of
Standard Bootstrap Loader)
Reserved
ST10 decoding
Bootstrap loader
45/180
Related parts for ST10F271E
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
St Series - Miniature Toggle Switches
Manufacturer:
Apem Components Ltd
Datasheet:
Part Number:
Description:
St Series Miniature Toggle Switches
Manufacturer:
Apem Components Ltd
Datasheet:
Part Number:
Description:
St1 Series Switch
Manufacturer:
e-switch
Datasheet:
Part Number:
Description:
ST1 Series
Manufacturer:
E-SWITCH [E-SWITCH]
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet: