ST10F271E STMICROELECTRONICS [STMicroelectronics], ST10F271E Datasheet - Page 99
ST10F271E
Manufacturer Part Number
ST10F271E
Description
16-bit MCU with 128 Kbyte Flash memory and 8/12 Kbyte RAM
Manufacturer
STMICROELECTRONICS [STMicroelectronics]
Datasheet
1.ST10F271E.pdf
(180 pages)
- Current page: 99 of 180
- Download datasheet (2Mb)
ST10F271B/ST10F271E
To ensure correct power-up reset with controlled supply current consumption, specially if
clock signal requires a long period of time to stabilize, an asynchronous hardware reset is
required during power-up. For this reason, it is recommended to connect the external R0-C0
circuit shown in Figure 30 to the RPD pin. On power-up, the logical low level on RPD pin
forces an asynchronous hardware reset when RSTIN is asserted low. The external pull-up
R0 will then charge the capacitor C0. Note that an internal pull-down device on RPD pin is
turned on when RSTIN pin is low, and causes the external capacitor (C0) to begin
discharging at a typical rate of 100-200µA. With this mechanism, after power-up reset, short
low pulses applied on RSTIN produce synchronous hardware reset. If RSTIN is asserted
longer than the time needed for C0 to be discharged by the internal pull-down device, then
the device is forced in an asynchronous reset. This mechanism insures recovery from very
catastrophic failure.
Figure 30. Minimum external reset circuitry
The minimum reset circuit of
the ST10F271 itself during software or watchdog triggered resets, because of the capacitor
C1 that will keep the voltage on RSTIN pin above V
sequence, and thus will trigger an asynchronous reset sequence.
Figure 31
used to generate power-up or manual reset, and R0-C0 circuit on RPD is used for power-up
reset and to exit from Power Down mode. Diode D1 creates a wired-OR gate connection to
the reset pin and may be replaced by open-collector Schmitt trigger buffer. Diode D2
provides a faster cycle time for repetitive power-on resets.
R2 is an optional pull-up for faster recovery and correct biasing of TTL Open Collector
drivers.
shows an example of a reset circuit. In this example, R1-C1 external circuit is only
ST10F271
Figure 30
RSTOUT
RSTIN
RPD
is not adequate when the RSTIN pin is driven from
+
+
V
CC
R0
C0
C1
External Hardware
IL
(and Interruptible
Power Down
mode)
b) For Power-up
Reset
after the end of the internal reset
a) Hardware
Reset
System reset
99/180
Related parts for ST10F271E
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
St Series - Miniature Toggle Switches
Manufacturer:
Apem Components Ltd
Datasheet:
Part Number:
Description:
St Series Miniature Toggle Switches
Manufacturer:
Apem Components Ltd
Datasheet:
Part Number:
Description:
St1 Series Switch
Manufacturer:
e-switch
Datasheet:
Part Number:
Description:
ST1 Series
Manufacturer:
E-SWITCH [E-SWITCH]
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet: