UPC8104 NEC, UPC8104 Datasheet
UPC8104
Available stocks
Related parts for UPC8104
UPC8104 Summary of contents
Page 1
... For evaluation sample order, please contact your local NEC sales office. (Order number: The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all devices/types available in every country. Please check with local NEC representative for availability and additional information. Document No. P10099EJ4V0DS00 (4th edition) ...
Page 2
... INTERNAL BLOCK DIAGRAM AND PIN CONNECTIONS (Top View) Lo1 in 1 Lo1 in 2 GND 3 (MOD GND 8 (UP Con) RF out 9 GND 10 (UP Con) APPLICATION EXAMPLE (PHS 90˚ REG. Phase 19 Power Save Shifter 18 GND 17 GND 16 MOD out ...
Page 3
ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL Supply Voltage V CC Power Save Voltage V PS Power Dissipation P D Operating Temperature T A Storage Temperature T stg Note 1: Mounted 1.6 mm double copper clad epoxy glass board ...
Page 4
STANDARD CHARACTERISTICS FOR REFERENCE ( 3.0 V, Unless Otherwise Specified PARAMETER SYMBOL UP CONVERTER BLOCK Up Con. Circuit Current I ccUpCon Up Con. Circuit Current at I cc(PS)UpCon Power-Save Mode Conversion Gain ...
Page 5
... This input impedance matched internally. Bypass of Lo1 input. This pin is grounded through internal capacitor. Open in case of single ended. Connect to the ground with minimum inductance. Track length should be kept as short as possible. Input for I signal. This input impedance is larger than Relations between amplitude ...
Page 6
... This pin is open collector output. IF input for Up-converter. This pin is high impedance input. Bypass of IF input. Grounded through external capacitor. Connect to the ground with minimum inductance. Track length should be kept as short as possible. Power save control pin can be controlled ON/SLEEP state with bias as follows; ...
Page 7
EXPLANATION OF INTERNAL FUNCTION BLOCK FUNCTION/OPERATION 90 PHASE Input signal from Lo1 is send to digital SHIFTER circuit of T-type flip-flop through frequency doubler. Output signal from T-type F/F is changed to same frequency as Lo1 input and that have ...
Page 8
TYPICAL CHARACTERISTICS ( Unless otherwise specified (single ended dBm, P Lo1in Lo2in SUPPLY VOLTAGE vs CIRCUIT CURRENT None 5 ...
Page 9
CONVERTER BLOCK] INPUT POWER vs OUTPUT POWER, IM +10 OIP = +0.2 dBm 3 0 –10 –20 –30 P RFout – –50 –60 f RFout f Lo2in P Lo2in – 240.0 MHz IFin1 f = ...
Page 10
CONVERTER BLOCK] SUPPLY VOLTAGE vs CONVERSION GAIN RF : 900 MHz Lo2 : 1 140 MHz, –20 dBm IF : 240 MHz, –20 dBm ...
Page 11
BLOCK] I/Q INPUT SIGNAL vs OUTPUT POWER, LOCAL LEAK, IMAGE REJECTION, I/Q 3RD ORDER INTERMODULATION DISTORTION 10 (PHS) 384 Kbps RNYQ = 0.5 (0000) All zero 0 P out –10 –20 –30 LOL (ISO ) LO –40 ImR –50 ...
Page 12
UP CONVERTER] TYPICAL SINE WAVE MODULATION OUTPUT SPECTRUM REF 0.0 dBm –ATT dB/ RBW 3 kHz VBW 10 kHz SWP 5.0 s CENTER 1.9000000 GHz <PHS> 384 Kbps, RNYQ = 0.5, MOD Pattern (0000), all ...
Page 13
RFout OUTPUT IMPEDANCE MARKER 3 1.9 GHz START 800.000 000 MHz Lo2in INPUT IMPEDANCE MARKER 2 1.66 GHz START 800.000 000 MHz 3; 162.25 –87.695 955. 900.000 000 MHz STOP 2 000.000 000 MHz 2; ...
Page 14
MODout OUTPUT IMPEDANCE MARKER 2 240 MHz START 50.000 000 MHz UP CON. in INPUT IMPEDANCE MARKER 2 240 MHz START 50.000 000 MHz 14 2; 49.244 13.58 9.0056 nH 240.000 000 MHz STOP 500.000 000 MHz ...
Page 15
Lo1in INPUT IMPEDANCE MARKER 2 240 MHz START 50.000 000 MHz TEST CIRCUIT (f = 1.9 GHz Lo1 Open S.G 1000 100 to 400 MHz Lo1 ...
Page 16
... case of this test board, the output signal from MOD. Lo2 is directly connected to the converter input port through 1000 pF, which is DC coupling. We recommend to insert a low pass filter between 3 pF MOD output and up converter RF input port to reject ...
Page 17
PACKAGE DIMENSIONS 20 PIN PLASTIC SSOP (225 mil) (UNIT: mm 6.7 0.3 1.8 MAX. 1.5 0.1 0.15 0.65 +0.10 0.10 M 0.22 –0.05 0.1 0.1 NOTE Each lead centerline is located within 0. its true position ...
Page 18
... Form a ground pattern as wide as possible to keep the minimum ground impedance (to prevent undesired oscillation). (3) Keep the track length of the ground pins as short as possible. (4) Connect a bypass capacitor (e.g. 1 000 pF) to the V ( offset voltage should be same as the offset voltage (to prevent changing the local leak level with power save control.) RECOMMENDED SOLDERING CONDITIONS This product should be soldered in the following recommended conditions ...
Page 19
Data Sheet P10099EJ4V0DS00 PC8104GR 19 ...
Page 20
... Specific: Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance ...