AD9300TE/883B AD [Analog Devices], AD9300TE/883B Datasheet - Page 3

• Manufacturer Part Number: AD9300TE/883B
• Description: 4 x 1 Wideband Video Multiplexer
• Manufacturer: AD [Analog Devices]

NOTES
11
12
13
14
15
16
17
18
19
10
11
12
13
14
15
16
17
18
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS
Supply Voltages ( V
Analog Input Voltage Each Input
Differential Voltage Between Any Two
Digital Input Voltages (A
Output Current
Operating Temperature Range
Storage Temperature Range . . . . . . . . . . . . –65 C to +150 C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . +175 C
Lead Soldering (10 sec) . . . . . . . . . . . . . . . . . . . . . . . +300 C
REV. A
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD9300 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
Permanent damage may occur if any one absolute maximum rating is exceeded. Functional operation is not implied, and device reliability may be impaired by
Measured at extremes of temperature range.
Measured as slope of V
Measured as worst deviation from endpoint fit with V
Full Power Bandwidth (FPBW) based on Slew Rate (SR). FPBW = SR/2 V
Measured between 20% and 80% transition points of 1 V output.
T-Step = Sin
Measured with a pulse input having slew rate >250 V/ s.
Measured at output between 0.28 V dc and 1.0 V dc with V
This specification is critically dependent on circuit layout. Value shown is measured with selected channel grounded and 10 MHz 2 V p-p signal applied to remaining
This specification is critically dependent on circuit layout. Value shown is measured with selected channel grounded and 10 MHz 2 V p-p signal applied to one other
Consult system timing diagram.
Measured from address change to 90% point of –2 V to +2 V output LOW-to-HIGH transition.
Measured from address change to 90% point of +2 V to –2 V output HIGH-to-LOW transition.
Measured from 50% transition point of ENABLE input to 90% transition of 0 V to –2 V and 0 V to +2 V output.
Measured from 50% transition point of ENABLE input to 10% transition of +2 V to 0 V and –2 V to 0 V output.
Measured while switching between two grounded channels.
Maximum power dissipation is a package-dependent parameter related to the following typical thermal impedances:
exposure to higher-than-recommended voltages for extended periods of time.
three channels. If selected channel is grounded through 75
channel. If selected channel is grounded through 75
(IN
Inputs (IN
Sinking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.0 mA
Sourcing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.0 mA
AD9300KQ/KP . . . . . . . . . . . . . . . . . . . . . . . 0 C to +70 C
1
thru IN
16-Pin Ceramic
20-Pin LCC
20-Pin PLCC
2
1
Step, when Step between 0 V and +700 mV points has 10% to 90% risetime = 125 ns.
thru IN
4
) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OUT
S
) . . . . . . . . . . . . . . . . . . . . . . . . . . 16 V
4
JA
JA
JA
) . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 V
versus V
Device
AD9300KQ
AD9300TE/883B
AD9300TQ/883B
AD9300KP
NOTES
1
2
= 87 C/W;
= 74 C/W;
= 71 C/W;
E = Ceramic Leadless Chip Carrier; P = Plastic Leaded Chip Carrier; Q = Cerdip.
For specifications, refer to Analog Devices Military Products Databook.
0
, A
1
IN
, ENABLE) . . . –0.5 V to +5.5 V
with V
JC
JC
JC
= 26 C/W
= 25 C/W
= 10 C/W
IN
l
= 1 V.
2
2
IN
Temperature
Range
0 C to +70 C
–55 C to +125 C
–55 C to +125 C
0 C to +70 C
, value is approximately 6 dB higher. Minimum specification in ( ) applies to DIPs.
= 1 V.
IN
, value is approximately 6 dB higher.
= 284 mV p-p at 3.58 MHz and 4.43 MHz.
ORDERlNG GUlDE
3.5 V
PEAK
Description
16-Pin Cerdip, Commercial
20-Pin LCC, Military Temperature
16-Pin Cerdip, Military Temperature Q-16
20-Pin PLCC, Commercial
–3–
EXPLANATION OF TEST LEVELS
Test Level I
Test Level II
Test Level III –
Test Level IV –
Test Level V
Test Level VI –
–
–
–
100% production tested.
100% production tested at +25 C, and
sample tested at specified temperatures.
Sample tested only.
Parameter is guaranteed by design and
characterization testing.
Parameter is a typical value only.
All devices are 100% production tested at
+25 C. 100% production tested at tempera-
ture extremes for military temperature de-
vices; sample tested at temperature extremes
for commercial/industrial devices.
Package
Option
Q-16
E-20A
P-20A
WARNING!
1
ESD SENSITIVE DEVICE
AD9300