OPA642N BURR-BROWN [Burr-Brown Corporation], OPA642N Datasheet - Page 3

• Manufacturer Part Number: OPA642N
• Description: Wideband, Low Distortion, Low Gain OPERATIONAL AMPLIFIER
• Manufacturer: BURR-BROWN [Burr-Brown Corporation]

PACKAGE/ORDERING INFORMATION
NOTES: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. (2) The “B” grade of the SO-8 and
DIP packages will be marked with a “B” by pin 8. The “B” grade of the SOT23-5 will be marked with a “B” near pins 3 and 4. (3) The SOT23-5 is only available on a 7"
tape and reel (e.g. ordering 250 pieces of “OPA642N-250” will get a single 250 piece tape and reel. Ordering 3000 pieces of “OPA642N-3k” will get a single 3000 piece
tape and reel). Please refer to Appendix B of Burr-Brown IC Data Book for detailed Tape and Reel Mechanical information.
Electrostatic discharge can cause damage ranging from per-
formance degradation to complete device failure. Burr-
Brown Corporation recommends that all integrated circuits
be handled and stored using appropriate ESD protection
methods.
ESD damage can range from subtle performance degrada-
tion to complete device failure. Precision integrated circuits
may be more susceptible to damage because very small
parametric changes could cause the device not to meet
published specifications.
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.
ABSOLUTE MAXIMUM RATINGS
PRODUCT
OPA642U
OPA642UB
OPA642N
OPA642NB
OPA642P
OPA642PB
Supply .......................................................................................... 6.0VDC
Internal Power Dissipation
Differential Input Voltage .................................................................. 1.2V
Input Voltage Range ............................................................................ V
Storage Temperature Range: P, PB, U, UB, N, NB ..... –40 C to +125 C
Lead Temperature (soldering, 10s) .............................................. +300 C
Junction Temperature (T
NOTE: (1) Packages must be derated based on specified
T
J
must be observed.
ELECTROSTATIC
DISCHARGE SENSITIVITY
(soldering, SO-8 3s) ....................................... +260 C
SO-8 Surface Mount
SO-8 Surface Mount
J
8-Pin Plastic DIP
8-Pin Plastic DIP
) ............................................................ +175 C
(1)
5-pin SOT23-5
5-pin SOT23-5
PACKAGE
.................................. See Thermal Analysis
NUMBER
PACKAGE
DRAWING
182
182
331
331
006
006
JA
(1)
. Maximum
S
TEMPERATURE
–40 C to +85 C
–40 C to +85 C
–40 C to +85 C
–40 C to +85 C
–40 C to +85 C
–40 C to +85 C
RANGE
3
PIN CONFIGURATION
NOTE: (1) Making use of all four power supply pins is recommended,
although not required. Using these four pins, instead of just pins 4 and 7, will
lower the power supply impedance improving distortion.
Top View
Non-Inverting Input
Non-Inverting Input
Inverting Input
Output
–V
NC
–V
S1
MARKING
PACKAGE
OPA642UB
OPA642PB
S
OPA642U
OPA642P
A42B
A42
1
2
3
4
1
2
3
(2)
OPA642
8
7
6
5
OPA642NB-250
5
4
OPA642N-250
OPA642NB-3k
OPA642N-3k
ORDERING
NUMBER
OPA642UB
OPA642PB
OPA642U
OPA642P
+V
Inverting Input
+V
+V
Output
–V
S
S2
S1
S2
(1)
(1)
(3)
DIP/SO-8
SOT23-5
®