HYB18T512800AF QIMONDA [Qimonda AG], HYB18T512800AF Datasheet - Page 4

• Manufacturer Part Number: HYB18T512800AF
• Description: 240-Pin Fully-Buffered DDR2 SDRAM Modules
• Manufacturer: QIMONDA [Qimonda AG]

1.2
This document describes the electrical and mechanical
features of a 240-pin, PC2-4200F, PC2-5300F ECC type,
Fully Buffered Double-Data-Rate Two Synchronous DRAM
Dual In-Line Memory Modules (DDR2 SDRAM FB-DIMMs).
Fully Buffered DIMMs use commodity DRAMs isolated from
the memory channel behind a buffer on the DIMM. They are
intended for use as main memory when installed in systems
such as servers and workstations. PC2-4200, PC2-5300
refers to the DIMM naming convention indicating the DDR2
SDRAMs running at 266, 333 MHz clock speed and offering
4200, 5300 MB/s peak bandwidth. FB-DIMM features a novel
architecture including the Advanced Memory Buffer. This
single chip component, located in the center of each DIMM,
acts as a repeater and buffer for all signals and commands
which are exchanged between the host controller and the
DDR2 SDRAMs including data in- and output. The AMB
communicates with the host controller and / or the adjacent
1) All product types end with a place code, designating the silicon die revision. Example: HYS 72T64000HFA-3.7-A, indicating Rev. A dice
2) The Compliance Code is printed on the module label and describes the speed grade, e.g. “PC2-4200F-444-11-A”, where 4200F means
Rev. 1.2, 2006-11
03292006-GUME-ERC3
Product Type
PC2-4200F (DDR2-533):
HYS72T64400HFD–3.7–A
HYS72T128420HFD–3.7–A
HYS72T256420HFD–3.7–A
PC2-5300F (DDR2-667):
HYS72T64400HFD–3S–A
HYS72T128420HFD–3S–A
HYS72T256420HFD–3S–A
are used for DDR2 SDRAM components. To learn more on QIMONDA DDR2 module and component nomenclature see section 8 of this
datasheet.
Fully Buffered DIMM with 4.26 GB/sec. Module Bandwidth and “444-11” means CAS latency = 4, t
JEDEC SPD Revision 1.1 and assembled on Raw Card “A”.
1)
Description
Compliance Code
512MB 1R×8 PC2–4200F–444–11–A
1GB 2R×8 PC2–4200F–444–11–B
2GB 2R×4 PC2–4200F–444–11–H
512MB 1R×8 PC2–4200F–444–11–A
PC2–4200F–444–11–B
2GB 2R×4 PC2–4200F–444–11–H
2)
Ordering Information (Pb-free components and assembly)
4
DIMMs on a system board using an Industry Standard High-
Speed Differential Point-to-Point Link Interface at 1.5 V.
The Advanced Memory Buffer also allows buffering of
memory traffic to support large memory capacities. All
memory control for the DRAM resides in the host, including
memory request initiation, timing, refresh, scrubbing, sparing,
configuration
Advanced Memory Buffer interface is responsible for handling
channel and memory requests to and from the local DIMM
and for forwarding requests to other DIMMs on the memory
channel. Fully Buffered DIMM provides a high memory
bandwidth, large capacity channel solution that has a narrow
host interface. The maximum memory capacity is 288 DDR2
SDRAM devices per channel or 8 DIMMs.
HYS72T[64/128/256]4[00/20]HFD–[3S/3.7]–A
Description
1 Rank, FB-DIMM
2 Ranks, FB-DIMM
2 Ranks, FB-DIMM
1 Rank, FB-DIMM
2 Ranks, FB-DIMM
2 Ranks, FB-DIMM
access,
and
rcd
latency = 4 and t
power
SDRAM Technology
512 Mbit (×8)
512 Mbit (×8)
512 Mbit (×4)
512 Mbit (×8)
512 Mbit (×8)
512 Mbit (×4)
Internet Data Sheet
management.
rp
latency = 4 using
TABLE 2
The