IS49NLC36160-25EBL ISSI, IS49NLC36160-25EBL Datasheet - Page 6

• Manufacturer Part Number: IS49NLC36160-25EBL
• Description: DRAM 576M, x36, 400Mhz RLDRAM2
• Manufacturer: ISSI

Specifications of IS49NLC36160-25EBL

• Rohs: yes
• Organization: 16 M x 36
• Package / Case: FBGA-144
• Memory Size: 576 Mbit
• Maximum Clock Frequency: 400 MHz
• Access Time: 2.5 ns
• Supply Voltage - Max: 2.63 V
• Supply Voltage - Min: 2.38 V
• Maximum Operating Current: 380 mA
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT

IS49NLC96400,IS49NLC18320,IS49NLC36160
2 Electrical Specifications
2.1 Absolute Maximum Ratings
Note: Stress greater than those listed in this table may cause permanent damage to the device. This is a stress rating only and functional operation of the device at
these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions
for extended periods may affect reliability.
2.2 DC Electrical Characteristics and Operating Conditions
Notes:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. If MRS bit A8 or Ax8 is 0, use RQ = 250Ω in the equation in lieu of presence of an external impedance matched resistor.
2.3 Capacitance (T
Note. These parameters are not 100% tested and capacitance is not tested on ZQ pin.
Integrated Silicon Solution, Inc. – www.issi.com –
Rev. 00F, 12/4/2012
Supply voltage
Supply voltage
Isolated output buffer supply
Reference voltage
Termination voltage
Input high voltage
Input low voltage
Output high current
Output low current
Clock input leakage current
Input leakage current
Output leakage current
Reference voltage current
I/O Voltage
Voltage on V
Voltage on V
Voltage on V
Address / Control Input capacitance
I/O, Output, Other capacitance (DQ, DM, QK, QVLD)
Clock Input capacitance
JTAG pins
All voltages referenced to V
Overshoot: V
may not have pulse widths less than t
V
Typically the value of V
Peak-to-peak AC noise on V
V
may not exceed ±2 percent of the DC value. Thus, from V
This measurement is to be taken at the nearest V
V
On-die termination may be selected using mode register A9 (for non-multiplexed address mode) or Ax9 (for multiplexed address mode). A resistance R
each data input signal to the nearest V
I
OH
DDQ
REF
TT
and I
is expected to be set equal to V
is expected to equal V
can be set to a nominal 1.5V ± 0.1V or 1.8V ± 0.1V supply.
Description
OL
are defined as absolute values and are measured at V
EXT
DD
DDQ
A
IH
= 25 °C, f = 1MHz)
(AC) ≤ V
supply relative to V
supply relative to V
supply relative to V
DD
REF
Parameter
+ 0.7V for t ≤ t
is expected to be 0.5 x V
DDQ
SS
REF
(GND).
/2 of the transmitting device and to track variations in the DC level of the same. Peak-to-peak noise (non-common mode) on V
must not exceed ±2 percent V
REF
Item
CK
and must track variations in the DC level of V
TT
/2 or operate at frequencies exceeding t
SS
SS
CK
SS
0V ≤ V
can be enabled. R
0V ≤ V
0V ≤ V
/2. Undershoot: V
V
V
Conditions
OH
OL
= V
= V
IN
REF
IN
IN
DDQ
DDQ
DDQ
≤ V
≤ V
≤ V
bypass capacitor.
of the transmitting device. V
/2
/2
DDQ
DD
DD
DDQ
TT
IL
REF
= 125–185Ω at 95°C T
/2, V
(AC) ≥ –0.5V for t ≤ t
(DC).
DDQ
REF
Symbol
/2. I
V
V
V
is allowed ±2 percent V
V
V
V
I
V
I
I
I
I
DDQ
I
REF
OH
OL
LO
EXT
REF
LC
DD
TT
LI
IH
IL
OH
flows from the device, I
Symbol
C
C
C
C
CLK
CK
IN
IO
J
(MAX).
REF
CK
C
REF
.
/2. During normal operation, V
is expected to track variations in V
.
(1.15 x RQ/5)
(1.15 x RQ/5)
0.49 x V
0.95 x V
V
V
(V
(V
REF
SSQ
DDQ
DDQ
2.38
Min
1.7
1.4
− 5
− 5
− 5
− 5
DDQ
+ 0.1
− 0.3
Test Conditions
/2)/
/2)/
− 0.3
− 0.3
− 0.3
− 0.3
/2 for DC error and an additional ±2 percent V
Min
DDQ
REF
OL
V
flows into the device.
V
V
V
CLK
IN
IO
J
=0V
=0V
=0V
=0V
(0.85 x RQ/5)
(0.85 x RQ/5)
0.51 x V
1.05 x V
DDQ
V
V
(V
(V
DDQ
REF
DDQ
DDQ
must not exceed V
Max
2.63
VDD
V
DDQ
1.9
5
5
5
5
− 0.1
DDQ
+ 0.3
/2)/
/2)/
.
Min
+ 2.8
+ 2.1
+ 2.1
Max
1.5
3.5
2.0
2.0
DDQ
REF
+ 0.3
Max
2.5
5.0
3.0
5.0
Units
DD
µA
µA
µA
µA
. Control input signals
A
A
V
V
V
V
V
V
V
DDQ
/2 for AC noise.
Units
9, 10, 11
9, 10, 11
V
V
V
V
Units
Notes
4,5,6
2,3
7,8
pF
pF
pF
pF
2
2
2
TT
6
from
REF