LPC1113FHN33/303,5 NXP Semiconductors, LPC1113FHN33/303,5 Datasheet - Page 203
LPC1113FHN33/303,5
Manufacturer Part Number
LPC1113FHN33/303,5
Description
ARM Microcontrollers - MCU Cortex-M0 24 kB flash up to 8kB SRAM
Manufacturer
NXP Semiconductors
Datasheet
1.LPC1113FHN333035.pdf
(538 pages)
Specifications of LPC1113FHN33/303,5
Rohs
yes
Core
ARM Cortex M0
Processor Series
LPC1113
Data Bus Width
32 bit
Maximum Clock Frequency
50 MHz
Program Memory Size
24 KB
Data Ram Size
4 KB
On-chip Adc
Yes
Operating Supply Voltage
1.8 V to 3.6 V
Operating Temperature Range
- 65 C to + 150 C
Package / Case
HVQFN-33
Mounting Style
SMD/SMT
Factory Pack Quantity
260
- Current page: 203 of 538
- Download datasheet (5Mb)
NXP Semiconductors
UM10398
User manual
Table 195. UART Line Status Register (U0LSR - address 0x4000 8014, Read Only) bit
Bit Symbol
3
4
5
6
7
31:
8
FE
BI
THRE
TEMT
RXFE
-
description
All information provided in this document is subject to legal disclaimers.
Value
-
0
1
0
1
0
1
0
1
0
1
Rev. 12 — 24 September 2012
…continued
Description
Framing Error. When the stop bit of a received character is a
logic 0, a framing error occurs. A U0LSR read clears
U0LSR[3]. The time of the framing error detection is
dependent on U0FCR0. Upon detection of a framing error, the
RX will attempt to re-synchronize to the data and assume that
the bad stop bit is actually an early start bit. However, it cannot
be assumed that the next received byte will be correct even if
there is no Framing Error.
Note: A framing error is associated with the character at the
top of the UART RBR FIFO.
Framing error status is inactive.
Framing error status is active.
Break Interrupt. When RXD1 is held in the spacing state (all
zeros) for one full character transmission (start, data, parity,
stop), a break interrupt occurs. Once the break condition has
been detected, the receiver goes idle until RXD1 goes to
marking state (all ones). A U0LSR read clears this status bit.
The time of break detection is dependent on U0FCR[0].
Note: The break interrupt is associated with the character at
the top of the UART RBR FIFO.
Break interrupt status is inactive.
Break interrupt status is active.
Transmitter Holding Register Empty. THRE is set immediately
upon detection of an empty UART THR and is cleared on a
U0THR write.
U0THR contains valid data.
U0THR is empty.
Transmitter Empty. TEMT is set when both U0THR and
U0TSR are empty; TEMT is cleared when either the U0TSR or
the U0THR contain valid data. This bit is updated as soon as
50 % of the first stop bit has been transmitted or a byte has
been written into the THR.
U0THR and/or the U0TSR contains valid data.
U0THR and the U0TSR are empty.
Error in RX FIFO. U0LSR[7] is set when a character with a RX
error such as framing error, parity error or break interrupt, is
loaded into the U0RBR. This bit is cleared when the U0LSR
register is read and there are no subsequent errors in the
UART FIFO.
U0RBR contains no UART RX errors or U0FCR[0]=0.
UART RBR contains at least one UART RX error.
Reserved
Chapter 13: LPC111x/LPC11Cxx UART
UM10398
© NXP B.V. 2012. All rights reserved.
203 of 538
Reset
Value
0
0
1
1
0
-
Related parts for LPC1113FHN33/303,5
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: