MAX492ESA-T Maxim Integrated, MAX492ESA-T Datasheet
MAX492ESA-T
Specifications of MAX492ESA-T
Available stocks
Related parts for MAX492ESA-T
MAX492ESA-T Summary of contents
Page 1
Not Recommended for New Designs The MAX495 was manufactured for Maxim by an outside wafer foundry using a process that is no longer available not recommended for new designs. A Maxim replacement or an industry second-source may be ...
Page 2
... High CMRR (90dB) and PSRR (110dB) Drives 1kΩ Load Drives Large Capacitive Loads MAX495 Available in µMAX Package—8-Pin SO ______________Ordering Information PART MAX492CPA MAX492CSA MAX492C/D MAX492EPA MAX492ESA MAX492MJA Ordering Information continued at end of data sheet. * Dice are specified at T _________________Pin Configurations TOP VIEW MAX187 ...
Page 3
Single/Dual/Quad, Micropower, Single-Supply Rail-to-Rail Op Amps ABSOLUTE MAXIMUM RATINGS Supply Voltage ( .................................................... Common-Mode Input Voltage..........(V CC Differential Input Voltage .........................................±(V Input Current (IN+, IN-, NULL1, NULL2) ..........................±10mA Output Short-Circuit Duration ....................Indefinite short circuit Voltage ...
Page 4
Single-Supply Rail-to-Rail Op Amps AC ELECTRICAL CHARACTERISTICS (V = 2. GND +25°C, unless otherwise noted PARAMETER Gain-Bandwidth Product R L Phase Margin R L Gain Margin R L Total Harmonic Distortion ...
Page 5
Single/Dual/Quad, Micropower, Single-Supply Rail-to-Rail Op Amps DC ELECTRICAL CHARACTERISTICS (V = 2. GND 0V PARAMETER Input Offset Voltage V CM Input Offset Voltage Tempco Input Bias Current V CM Input ...
Page 6
Single-Supply Rail-to-Rail Op Amps DC ELECTRICAL CHARACTERISTICS (V = 2. GND 0V PARAMETER Input Offset Voltage Input Offset Voltage Tempco Input Bias Current Input Offset Current Common-Mode Input Voltage Range ...
Page 7
Single/Dual/Quad, Micropower, Single-Supply Rail-to-Rail Op Amps __________________________________________Typical Operating Characteristics (T = +25° 5V 0V, unless otherwise noted GAIN AND PHASE vs. FREQUENCY MAX492- GAIN 40 20 PHASE 0 - ...
Page 8
Single-Supply Rail-to-Rail Op Amps ____________________________Typical Operating Characteristics (continued +25° 5V 0V, unless otherwise noted LARGE-SIGNAL GAIN vs. OUTPUT VOLTAGE 120 R = 10k L 110 100 ...
Page 9
Single/Dual/Quad, Micropower, Single-Supply Rail-to-Rail Op Amps ____________________________Typical Operating Characteristics (continued +25° 5V 0V, unless otherwise noted VOLTAGE-NOISE DENSITY vs. FREQUENCY 100 10 INPUT REFERRED 1 0.01 0.1 1 FREQUENCY (kHz) TOTAL ...
Page 10
Single-Supply Rail-to-Rail Op Amps ____________________________Typical Operating Characteristics (continued +25° 5V 0V, unless otherwise noted LARGE-SIGNAL TRANSIENT RESPONSE 50 s/div V = +5V + 10k ...
Page 11
Single/Dual/Quad, Micropower, Single-Supply Rail-to-Rail Op Amps __________Applications Information The dual MAX492, quad MAX494, and single MAX495 op amps combine excellent DC accuracy with rail-to- rail operation at both input and output. With their preci- sion performance, wide dynamic range at ...
Page 12
Single-Supply Rail-to-Rail Op Amps the op amp in an inverting configuration (Figure 3a); connect resistor R3 between the noninverting input and the input signal when using the op amp in a noninvert- ing configuration (Figure 3b). Select R3 to equal ...
Page 13
Single/Dual/Quad, Micropower, Single-Supply Rail-to-Rail Op Amps in series with IN-, IN+, or both. Series resistors are not recommended for amplifier applications, as they may increase input offsets and decrease amplifier bandwidth. Output Loading and Stability Even with their low quiescent ...
Page 14
Single-Supply Rail-to-Rail Op Amps The MAX492/MAX494/MAX495 can drive capacitive loads in excess of 1000pF under certain conditions (Figure 5). When driving capacitive loads, the greatest potential for instability occurs when the op amp is sourcing approximately 100µA. Even in this ...
Page 15
Single/Dual/Quad, Micropower, Single-Supply Rail-to-Rail Op Amps 5 s/div Figure 11a. Power-Up Settling Time (V CC Because the MAX492/MAX494/MAX495 have excellent stability, no isolation resistor is required, except in the most demanding applications. This is beneficial because an isolation resistor would ...
Page 16
Single-Supply Rail-to-Rail Op Amps _Ordering Information (continued) PART TEMP. RANGE MAX494CPD 0°C to +70°C MAX494CSD 0°C to +70°C MAX494EPD -40°C to +85°C MAX494ESD -40°C to +85°C MAX494MJD -55°C to +125°C MAX495CPA 0°C to +70°C MAX495CSA 0°C to +70°C MAX495CUA 0°C ...
Page 17
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 16 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600 © 1996 Maxim Integrated Products C 0 ...