C8051F313R Silicon Labs, C8051F313R Datasheet - Page 101

• Manufacturer Part Number: C8051F313R
• Description: 8-bit Microcontrollers - MCU 8KB 10ADC
• Manufacturer: Silicon Labs

Specifications of C8051F313R

• Product Category: 8-bit Microcontrollers - MCU
• Core: 8051
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 25 MHz
• Program Memory Size: 8 KB
• Data Ram Size: 1.25 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 2.7 V to 3.6 V
• Package / Case: QFN-28
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 17
• Data Rom Size: 128 B
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 25
• Number Of Timers: 5
• On-chip Dac: No
• Processor Series: C8051
• Program Memory Type: Flash
• Factory Pack Quantity: 1500
• Supply Voltage - Max: 3.6 V
• Supply Voltage - Min: 2.7 V

Bit7:
Bits6–4: IN1SL2–0: /INT1 Port Pin Selection Bits
Bit3:
Bits2–0: INT0SL2–0: /INT0 Port Pin Selection Bits
Note: Refer to SFR Definition 17.1 for INT0/1 edge- or level-sensitive interrupt selection.
IN1PL
R/W
Bit7
IN1PL: /INT1 Polarity
0: /INT1 input is active low.
1: /INT1 input is active high.
These bits select which Port pin is assigned to /INT1. Note that this pin assignment is inde-
pendent of the Crossbar; /INT1 will monitor the assigned Port pin without disturbing the
peripheral that has been assigned the Port pin via the Crossbar. The Crossbar will not
assign the Port pin to a peripheral if it is configured to skip the selected pin (accomplished by
setting to ‘1’ the corresponding bit in register P0SKIP).
IN0PL: /INT0 Polarity
0: /INT0 interrupt is active low.
1: /INT0 interrupt is active high.
These bits select which Port pin is assigned to /INT0. Note that this pin assignment is inde-
pendent of the Crossbar. /INT0 will monitor the assigned Port pin without disturbing the
peripheral that has been assigned the Port pin via the Crossbar. The Crossbar will not
assign the Port pin to a peripheral if it is configured to skip the selected pin (accomplished by
setting to ‘1’ the corresponding bit in register P0SKIP).
IN1SL2–0
IN0SL2–0
IN1SL2
R/W
Bit6
000
001
010
100
101
000
001
010
100
101
011
110
111
011
110
111
SFR Definition 8.11. IT01CF: INT0/INT1 Configuration
IN1SL1
R/W
Bit5
/INT1 Port Pin
/INT0 Port Pin
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
IN1SL0
R/W
Bit4
Rev. 1.7
IN0PL
R/W
Bit3
C8051F310/1/2/3/4/5/6/7
IN0SL2
R/W
Bit2
IN0SL1
R/W
Bit1
IN0SL0
R/W
Bit0
SFR Address:
00000001
Reset Value
0xE4
101