ZLF645S2864GP0001 Maxim Integrated, ZLF645S2864GP0001 Datasheet - Page 98
ZLF645S2864GP0001
Manufacturer Part Number
ZLF645S2864GP0001
Description
8-bit Microcontrollers - MCU Crimzon Flash Infrared MCU
Manufacturer
Maxim Integrated
Datasheet
1.ZLF645E0H4864G2204.pdf
(201 pages)
Specifications of ZLF645S2864GP0001
Core
Z8
Data Bus Width
8 bit
Maximum Clock Frequency
8 MHz
Program Memory Size
64 KB
Data Ram Size
1 KB
Operating Supply Voltage
2 V to 3.6 V
Interface Type
UART
Number Of Programmable I/os
5
Number Of Timers
2 x 8 bit, 1 x 16 bit
Processor Series
ZLF645
Program Memory Type
Flash
- Current page: 98 of 201
- Download datasheet (2Mb)
19-4572; Rev 0; 4/09
Note:
UART Interrupts
The UART is now configured for interrupt-driven data reception. When the UART
Receiver interrupt is detected, the associated ISR performs the following:
1. Checks the UART Status register to determine the source of the interrupt, whether it is
2. Reads the data from the UART Receive Data register, if the interrupt was caused by
3. Clears the UART receiver interrupt in the applicable Interrupt Request register.
4. Executes the IRET instruction to return from the ISR and await more data.
The UART features separate interrupts for the transmitter and the receiver. In addition,
when the UART primary functionality is disabled, the BRG can also function as a basic
timer with interrupt capability.
When the UART is set to run at higher baud rates, the UART receiver’s service routine
may not have enough time to read and manipulate all bits in the UART Status register
(especially bits generating error conditions) for a received byte before the next byte is
received. You can devise your own hand-shaking protocol to prevent the transmitter from
transmitting more data while current data is being serviced.
Transmitter Interrupts
The transmitter generates a single interrupt when the Transmit Status bit, UST[2], is set
to 1. This indicates that the transmitter is ready to accept new data for transmission. The
Transmit Status interrupt occurs after the internal transmit shift register has shifted the first
bit of data out. At this point, the Transmit Data register can be written with the next char-
acter to send. This provides 7 bit periods of latency to load the Transmit Data register
before the transmit shift register completes shifting the current character. Writing to the
UART Transmit Data register clears the UST[2] bit to 0. The interrupt is cleared by
writing a 0 to the Transmit Data register.
Receiver Interrupts
The receiver generates an interrupt when any of the following occurs:
•
•
an error, break, or received data.
data available.
A data byte is received and available in the UART Receive Data register—This
interrupt can be disabled independent of the other receiver interrupt sources. The
received data interrupt occurs once the receive character has been received and placed
in the Receive Data register. Software must respond to this received data available
condition before the next character is completely received to avoid an overrun error.
The interrupt is cleared by reading from the UART Receive Data register.
A break is received—A break is detected when a 0 is sent to the receiver for the full
byte plus the parity and stop bits. After a break is detected, it will interrupt
ZLF645 Series Flash MCUs
Product Specification
Operation
90
Related parts for ZLF645S2864GP0001
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: