ZLF645S2864GP0001T Maxim Integrated, ZLF645S2864GP0001T Datasheet - Page 99
ZLF645S2864GP0001T
Manufacturer Part Number
ZLF645S2864GP0001T
Description
8-bit Microcontrollers - MCU Crimzon Flash Infrared MCU
Manufacturer
Maxim Integrated
Datasheet
1.ZLF645E0H4864G2204.pdf
(201 pages)
Specifications of ZLF645S2864GP0001T
Core
Z8
Data Bus Width
8 bit
Maximum Clock Frequency
8 MHz
Program Memory Size
64 KB
Data Ram Size
1 KB
Operating Supply Voltage
2 V to 3.6 V
Interface Type
UART
Number Of Programmable I/os
5
Number Of Timers
2 x 8 bit, 1 x 16 bit
Processor Series
ZLF645
Program Memory Type
Flash
- Current page: 99 of 201
- Download datasheet (2Mb)
19-4572; Rev 0; 4/09
Note:
•
•
Ensure that the transmitter uses the same stop bit configuration as the receiver.
UART Overrun Errors
When an overrun error condition occurs the UART prevents overwriting of the valid data
currently in the Receive Data register. The Break Detect and Overrun status bits are not
displayed until after the valid data has been read.
After the valid data has been read, the UART Status (UST) register is updated to indicate
the overrun condition (and Break Detect, if applicable). The UST[7] bit is set to 1 to
indicate that the Receive Data register contains a data byte. However, because the overrun
error occurred, this byte may not contain valid data and must be ignored. The Break Detect
bit, UST[3], indicates if the overrun was caused by a break condition on the line. After
reading the status byte indicating an overrun error, the Receive Data register must be read
again to clear the error bits is the UART Status 0 register. Updates to the Receive Data reg-
ister occur only when the next data word is received.
UART Data and Error Handling Procedure
Figure 25
interrupt service routine.
immediately if there is no valid data in the Receive Data register. If data is present in
the Receive Data register, an interrupt will occur after the UART Receive Data
register is read.
An overrun is detected—An overrun occurs when a byte of data is received while
there is valid data in the UART Receive Data register that has not been read by the
user. The interrupt will be generated when the user reads the UART Receive Data
register. The interrupt is cleared by reading the UART Receive Data register. When an
overrun error occurs, the additional data byte will not overwrite the data currently
stored in the UART Receive Data register.
A data framing error is detected—A data framing error is detected when the first
stop bit is 0 instead of 1. When configured for 2 stop bits, a data framing error is only
detected when the first stop bit is 0. A framing error interrupt is generated when the
framing error is detected. Reading the UART Receive Data register clears the
interrupt.
on page 92 displays the recommended procedure for use in UART receiver
ZLF645 Series Flash MCUs
Product Specification
Operation
91
Related parts for ZLF645S2864GP0001T
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: