C8051F314R Silicon Labs, C8051F314R Datasheet - Page 69

no-image

C8051F314R

Manufacturer Part Number
C8051F314R
Description
8-bit Microcontrollers - MCU 8KB 10ADC
Manufacturer
Silicon Labs
Datasheet

Specifications of C8051F314R

Product Category
8-bit Microcontrollers - MCU
Core
8051
Data Bus Width
8 bit
Maximum Clock Frequency
25 MHz
Program Memory Size
8 KB
Data Ram Size
1.25 KB
On-chip Adc
Yes
Operating Supply Voltage
2.7 V to 3.6 V
Package / Case
LQFP-32
Mounting Style
SMD/SMT
A/d Bit Size
10 bit
A/d Channels Available
17
Data Rom Size
128 B
Interface Type
I2C, SMBus, SPI, UART
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Number Of Programmable I/os
29
Number Of Timers
5
On-chip Dac
No
Processor Series
C8051
Program Memory Type
Flash
Factory Pack Quantity
500
Supply Voltage - Max
3.6 V
Supply Voltage - Min
2.7 V
7.
C8051F31x devices include two on-chip programmable voltage comparators: Comparator0 is shown in
Figure 7.1; Comparator1 is shown in Figure 7.2. The two comparators operate identically with the following
exceptions: (1) Their input selections differ as shown in Figure 7.1 and Figure 7.2; (2) Comparator0 can be
used as a reset source.
The Comparator offers programmable response time and hysteresis, an analog input multiplexer, and two
outputs that are optionally available at the Port pins: a synchronous “latched” output (CP0, CP1), or an
asynchronous “raw” output (CP0A, CP1A). The asynchronous CP0A signal is available even when the
system clock is not active. This allows the Comparator to operate and generate an output with the device
in STOP mode. When assigned to a Port pin, the Comparator output may be configured as open drain or
push-pull (see
reset source (see
The Comparator0 inputs are selected in the CPT0MX register (SFR Definition 7.2). The CMX0P1-CMX0P0
bits select the Comparator0 positive input; the CMX0N1-CMX0N0 bits select the Comparator0 negative
input. The Comparator1 inputs are selected in the CPT1MX register (SFR Definition 7.5). The CMX1P1-
CMX1P0 bits select the Comparator1 positive input; the CMX1N1-CMX1N0 bits select the Comparator1
negative input.
Important Note About Comparator Inputs: The Port pins selected as comparator inputs should be con-
figured as analog inputs in their associated Port configuration register, and configured to be skipped by the
Crossbar (for details on Port configuration, see
Comparators
CMX0N1
CMX0N0
CMX0P1
CMX0P0
Section “13.2. Port I/O Initialization” on page
Section “9.5. Comparator0 Reset” on page
Figure 7.1. Comparator0 Functional Block Diagram
P1.0
P1.4
P2.0
P2.4
P1.1
P1.5
P2.1
P2.5
CP0HYP1
CP0HYP0
CP0HYN1
CP0HYN0
CP0OUT
CP0RIF
CP0EN
CP0FIF
CP0 +
CP0 -
CP0MD1
CP0MD0
CP0RIE
CP0FIE
Section “13.3. General Purpose Port I/O” on page
Rev. 1.7
+
-
VDD
GND
C8051F310/1/2/3/4/5/6/7
Decision
Reset
Tree
133). Comparator0 may also be used as a
108).
(SYNCHRONIZER)
D
SET
CLR
Q
Q
D
SET
CLR
Q
Q
Rising-edge
CP0
Crossbar
Interrupt
Logic
Falling-edge
Interrupt
CP0
CP0A
CP0
CP0
135).
69

Related parts for C8051F314R