MAX17019NEVKIT+ Maxim Integrated, MAX17019NEVKIT+ Datasheet - Page 3
![no-image](/images/no-image-200.jpg)
MAX17019NEVKIT+
Manufacturer Part Number
MAX17019NEVKIT+
Description
Power Management IC Development Tools Maxim Evaluation Kit
Manufacturer
Maxim Integrated
Series
MAX17019r
Datasheet
1.MAX17019NEVKIT.pdf
(8 pages)
Note: Indicate that you are using the MAX17019 when contacting these component suppliers.
•
•
•
•
•
The EV kit is a fully assembled and tested surface-mount
board. Follow the steps below to verify board operation.
Caution: Do not turn on the power supply until all
connections are completed.
1)
2)
AVX Corporation
Central Semiconductor Corp.
Fairchild Semiconductor
Murata Manufacturing Co., Ltd.
NEC TOKIN America, Inc.
SANYO Electric Company, Ltd.
Taiyo Yuden
TDK Corp.
TOKO America, Inc.
Vishay
Würth Electronik GmbH & Co. KG
MAX17019N EV kit
6V to 38V, 100W DC power supply
Four dummy loads capable of sinking 4A each
Four digital multimeters
100MHz dual-trace oscilloscope
Ensure that the circuit is connected correctly to the
power supply and dummy loads prior to applying
any power.
Set SW1 (1, 10) to the on position (SHDN = VBATT,
IC enabled).
Set SW1 (2, 9) to the on position (ONA = VDD,
VOUTA enabled).
Set SW1 (3, 8) to the on position (ONB = VDD,
VOUTB enabled).
Set SW1 (4, 7) to the on position (ONC = VDD,
VOUTC enabled).
Set SW1 (5, 6) to the on position (OND = VDD,
VOUTD enabled).
_______________________________________________________________________________________
SUPPLIER
Required Equipment
Quick Start
Procedure
MAX17019N Evaluation Kit
843-946-0238
631-435-1110
888-522-5372
770-436-1300
408-324-1790
619-661-6835
800-348-2496
847-803-6100
847-297-0070
402-564-3131
201-785-8800
PHONE
3)
4)
5)
The MAX17019N EV kit is shipped with FBA connected
to resistors R5 and R6, which sets the VOUTA voltage
to 5V.
To change the output voltage to a value between 1V
and 5.3V, remove R5. Calculate R5 using the following
equation:
where VFBA = 1V and R6 =10kI Q1%. For an output
voltage of 1V, place a short across R5 and leave R6
open.
Detailed Description of Hardware
Connect the first DMM across the VOUTA and
GND PCB pads.
Connect the second DMM across the VOUTB and
GND PCB pads.
Connect the third DMM across the VOUTC and
GND PCB pads.
Connect the fourth DMM across the VOUTD and
GND PCB pads.
Turn on the power supply and adjust the input volt-
age to 12V.
Verify that the output voltages are VOUTA = 5V,
VOUTB = 1.8V, VOUTC = 1.05V, and VOUTD = 0.9V.
www.avx.com
www.centralsemi.com
www.fairchildsemi.com
www.murata.com
www.nec-tokinamerica.com
www.sanyodevice.com
www.t-yuden.com
www.component.tdk.com
www.tokoam.com
www.vishay.com
www.we-online.com
5V Output-Voltage Setting (VOUTA)
R5 = R6 [(VOUTA/VFBA) - 1]
Component Suppliers
WEBSITE
3