M93C56-RDS6G STMicroelectronics, M93C56-RDS6G Datasheet - Page 5
![IC EEPROM 2KBIT 1MHZ 8TSSOP](/photos/5/43/54342/497-8-tssop_sml.jpg)
M93C56-RDS6G
Manufacturer Part Number
M93C56-RDS6G
Description
IC EEPROM 2KBIT 1MHZ 8TSSOP
Manufacturer
STMicroelectronics
Datasheet
1.M93C46-RDS6G.pdf
(30 pages)
Specifications of M93C56-RDS6G
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
2K (256 x 8 or 128 x 16)
Speed
1MHz
Interface
Microwire, 3-Wire Serial
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-TSSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
cle, a Busy/Ready signal is available on Serial
Data Output (Q) when Chip Select Input (S) is driv-
en High.
An internal Power-on Data Protection mechanism
in the M93Cx6 inhibits the device when the supply
is too low.
Figure 3. DIP, SO and TSSOP Connections
Note: 1. See page 23 (onwards) for package dimensions, and how
Figure 4. 90° Turned-SO Connections
Note: 1. See page 26 for package dimensions, and how to identify
2. DU = Don’t Use.
2. DU = Don’t Use.
to identify pin-1.
pin-1.
V CC
DU
Q
C
D
C
S
S
1
2
3
4
1
2
3
4
M93Cx6
M93Cx6
AI01929B
AI00900B
8
7
6
5
8
7
6
5
V CC
DU
ORG
V SS
ORG
V SS
Q
D
M93C86, M93C76, M93C66, M93C56, M93C46, M93C06
The DU (Don’t Use) pin does not contribute to the
normal operation of the device. It is reserved for
use by STMicroelectronics during test sequences.
The pin may be left unconnected or may be con-
nected to V
V
er consumption.
MEMORY ORGANIZATION
The M93Cx6 memory is organized either as bytes
(x8) or as words (x16). If Organization Select
(ORG) is left unconnected (or connected to V
the x16 organization is selected; when Organiza-
tion Select (ORG) is connected to Ground (V
the x8 organization is selected. When the M93Cx6
is in stand-by mode, Organization Select (ORG)
should be set either to V
power consumption. Any voltage between V
and V
may increase the stand-by current.
POWER-ON DATA PROTECTION
To prevent data corruption and inadvertent write
operations during power-up, a Power-On Reset
(POR) circuit resets all internal programming cir-
cuitry, and sets the device in the Write Disable
mode.
– At Power-up and Power-down, the device must
– When V
For the M93Cx6 devices (5V range) the POR
threshold voltage is around 3V. For the M93Cx6-
W (3V range) and M93Cx6-R (2V range) the POR
threshold voltage is around 1.5V.
SS
not be selected (that is, Chip Select Input (S)
must be driven Low) until the supply voltage
reaches the operating value V
Table 8 to Table 10.
properly reset (in the Write Disable mode) and
is ready to decode and execute incoming in-
structions.
is recommended for the lowest stand-by pow-
CC
applied to Organization Select (ORG)
CC
CC
reaches its valid level, the device is
or V
SS
. Direct connection of DU to
SS
or V
CC
CC
for minimum
specified in
5/30
CC
SS
SS
)
)