MD4811-D512-V3Q18-X-P/Y SanDisk, MD4811-D512-V3Q18-X-P/Y Datasheet - Page 21
MD4811-D512-V3Q18-X-P/Y
Manufacturer Part Number
MD4811-D512-V3Q18-X-P/Y
Description
IC MDOC G3 512MB 48-TSOP
Manufacturer
SanDisk
Datasheet
1.MD4331-D1G-V3Q18-X-PY.pdf
(97 pages)
Specifications of MD4811-D512-V3Q18-X-P/Y
Format - Memory
FLASH
Memory Type
FLASH - Nand
Memory Size
512M (64M x 8)
Speed
55ns
Interface
Parallel
Voltage - Supply
2.5 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
48-TSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
585-1136
- Current page: 21 of 97
- Download datasheet (2Mb)
18
The following abbreviations are used: IN - Standard (non-Schmidt) input, ST - Schmidt Trigger input, OD - Open drain output, R8 - Nominal
22K pull-up resistor, enabled only for 8-bit interface mode (IF_CFG input is 0)
IRQ#
DPD
VCC
VCCQ
VSS
RSRVD
Signal
See Figure 4
Ball No.
G3, J9
G2
F9
E4
J5
J6
M
A
Input
Type
OD
ST
-
-
-
-
-
-
Preliminary Data Sheet, Rev. 1.1
Device supply. Requires a 10 nF and 0.1 μF
I/O power supply. Sets the logic ‘1’ voltage level
Interrupt Request, active low. A 10 KΩ pull-up
resistor is required if this ball drives an input. A 10
KΩ pull-up resistor is recommended even if this
ball is not used.
Deep Power-Down. Used to enter and exit Deep
Power-Down mode. Pin is assigned A0 instead of
DPD when working in 8-bit mode.
capacitor.
range of I/O balls. VCCQ may be either 2.5V to
3.6V or 1.65V to 2.0V. Requires a 10 nF and
0.1 μF capacitor.
Ground. All VSS balls must be connected.
Reserved. If compatibility with previous
DiskOnChip versions is necessary:
In 16-bit mode (IF_CFG = 1) this ball must be
connected to GND for compatibility with G2
devices.
In 8-bit mode (IF_CFG = 0) may be left floating.
Refer to application note AP-DOC-067 for design
guidelines when migrating from previous
DiskOnChip versions (G2).
Reserved. Other reserved signals are not
connected internally and must be left floating to
guarantee forward compatibility with future
products.
Mechanical. These balls are for mechanical
placement, and are not connected internally.
Alignment. This ball is for device alignment and is
not connected internally.
Power
Other
Description
Mobile DiskOnChip G3
91-SR-011-05-8L
Supply
Supply
Supply
Signal
Output
Type
Input
Related parts for MD4811-D512-V3Q18-X-P/Y
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC MDOC G3 512MB 48-TSOP
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC G3 512MB 48-TSOP
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC G3 512MB 48-TSOP
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC G4 2GB 69-FBGA
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC P3 256MB 48-TSOP
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC P3 256MB 48-TSOP
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC P3 256MB 48-TSOP
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC H1 8GB 115-FBGA
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC H3 1GB FBGA
Manufacturer:
SanDisk
Datasheet:
Part Number:
Description:
IC MDOC H3 2GB FBGA
Manufacturer:
SanDisk
Datasheet: