LT1910ES8#TRPBF Linear Technology, LT1910ES8#TRPBF Datasheet
LT1910ES8#TRPBF
Specifications of LT1910ES8#TRPBF
Available stocks
Related parts for LT1910ES8#TRPBF
LT1910ES8#TRPBF Summary of contents
Page 1
... The device will not sustain damage from supply transients of –15V to 60V. The LT1910 is available in the SO-8 package. L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. 24V ...
Page 2
... Junction Temperature Range ................ –40°C to 125°C Storage Temperature Range ................... –65°C to 150°C Lead Temperature (Soldering, 10 sec) .................. 300°C ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL LT1910ES8#PBF LT1910ES8#TRPBF LT1910IS8#PBF LT1910IS8#TRPBF LEAD BASED FINISH TAPE AND REEL LT1910ES8 LT1910ES8#TR LT1910IS8 LT1910IS8#TR Consult LTC Marketing for parts specifi ...
Page 3
ELECTRICAL CHARACTERISTICS temperature range, otherwise specifi cations are at T SYMBOL PARAMETER I Drain Sense Input Current SENSE + V – V Gate Voltage Above Supply GATE FAULT Output High Threshold Voltage V F(TH) FAULT Output Low Threshold Voltage FAULT ...
Page 4
LT1910 TYPICAL PERFORMANCE CHARACTERISTICS Input Current vs Temperature 200 180 160 140 120 IN 100 –50 – 100 TEMPERATURE (°C) 1910 G04 Timer Charge ...
Page 5
TYPICAL PERFORMANCE CHARACTERISTICS Turn-On Time vs Temperature 400 + V = 24V V = 32V GATE 350 C = 1nF GATE 300 250 200 150 100 – 100 –25 TEMPERATURE ( C) 1910 G13 PIN FUNCTIONS ...
Page 6
LT1910 PIN FUNCTIONS Information). A maximum of 10kΩ can be inserted between a drain-sense resistor and the SENSE pin. If current sensing is not required, the SENSE pin is tied to supply. BLOCK DIAGRAM + V 14μA – + 3.3V ...
Page 7
OPERATION also activates the open-collector NPN to pull the FAULT pin LOW, indicating an overcurrent condition. When the MOSFET gate voltage is discharged to less than 1.4V, the TIMER pin is released. The 14μA current source then slowly charges the ...
Page 8
LT1910 APPLICATIONS INFORMATION to the supply at the same point as the positive end of the sense resistor. The drain-sense threshold voltage has a positive tempera- ture coeffi cient, allowing PTC sense resistors to be used (see Printed Circuit Board ...
Page 9
APPLICATIONS INFORMATION The turn-on current spike into C LOAD V – • PEAK LOAD R C • where V is the MOSFET gate threshold voltage obtained by plotting the equation: ...
Page 10
LT1910 APPLICATIONS INFORMATION Low Voltage/Wide Supply Range Operation When the supply is less than 12V, the LT1910’s charge pump does not produce suffi cient gate voltage to fully enhance the standard N-channel MOSFET. For these ap- plications, a logic-level MOSFET ...
Page 11
... MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm) Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa- tion that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 12
... High Speed Single/Dual N-Channel/P-Channel MOSFET Drivers LTC1710 SMBus Dual Monolithic High Side Switch LTC4412 Low Loss PowerPath™ Controller PowerPath and ThinSOT are trademarks of Linear Technology Corporation. Linear Technology Corporation 12 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 ● ...