ISL6594BCB Intersil, ISL6594BCB Datasheet
ISL6594BCB
Specifications of ISL6594BCB
Available stocks
Related parts for ISL6594BCB
ISL6594BCB Summary of contents
Page 1
... CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. | 1-888-INTERSIL or 1-888-468-3774 Intersil (and design registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2004, 2005-2007. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ...
Page 2
... PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. Pinouts ISL6594ACB, ISL6594BCB (8 LD SOIC) TOP VIEW UGATE ...
Page 3
Typical Application - 4-Channel Converter Using ISL6592 and ISL6594A Gate Drivers +12V +5V +3.3V VDD V12_SEN GND ISL6592 OUT1 VID4 OUT2 VID3 ISEN1 VID2 OUT3 OUT4 VID1 ISEN2 FROM µP VID0 OUT5 VID5 OUT6 LL0 ISEN3 LL1 OUTEN OUT7 OUT8 ...
Page 4
... Maximum Junction Temperature (Plastic Package +150° 0.3V Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C DC BOOT + 0.3V Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below BOOT 0.3V http://www.intersil.com/pbfree/Pb-FreeReflow.asp DC PVCC + 0.3V PVCC to 15V (V = 12V) DC PVCC Recommended Operating Conditions Ambient Temperature Range 0°C to +85°C Maximum Operating Junction Temperature +125° ...
Page 5
Electrical Specifications Recommended Operating Conditions, Unless Otherwise Noted. (Continued) PARAMETER LGATE Rise Time UGATE Fall Time (Note 4) LGATE Fall Time (Note 4) UGATE Turn-On Propagation Delay (Note 4) LGATE Turn-On Propagation Delay (Note 4) UGATE Turn-Off Propagation Delay (Note ...
Page 6
... PHASE falls to less than +0.8V, the LGATE is released to turn on. Three-State PWM Input A unique feature of these drivers and other Intersil drivers is the addition of a shutdown window to the PWM input. If the PWM signal enters and remains within the shutdown window for a set hold off time, the driver outputs are disabled and both MOSFET gates are pulled and held low ...
Page 7
In addition, more than 400mV hysteresis also incorporates into the three-state shutdown window to eliminate PWM input oscillations due to the capacitive load seen by the PWM input through the body diode of the controller’s PWM output when the power-up ...
Page 8
MOSFETs. The total gate drive power losses due to the gate charge of MOSFETs and the driver’s internal circuitry and their corresponding average driver current can be estimated with Equations 2 and 3, respectively: • ...
Page 9
... The pin #1 identifier may be either a mold or mark feature. 7. Dimensions D2 and E2 are for the exposed pads which provide NX b improved electrical and thermal performance Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. 0. 0.200 ...
Page 10
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...