ADM1027ARQ ON Semiconductor, ADM1027ARQ Datasheet - Page 35
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
ADM1027ARQ
Manufacturer Part Number
ADM1027ARQ
Description
IC THER CTRL VOLT/MONITOR 24QSOP
Manufacturer
ON Semiconductor
Series
dBCool®r
Datasheet
1.ADM1027ARQ.pdf
(56 pages)
Specifications of ADM1027ARQ
Rohs Status
RoHS non-compliant
Function
Fan Control, Temp Monitor
Topology
ADC, Comparator, Fan Speed Counter, Multiplexer, Register Bank
Sensor Type
External & Internal
Sensing Temperature
0°C ~ 105°C, External Sensor
Output Type
SMBus™
Output Alarm
No
Output Fan
Yes
Voltage - Supply
3 V ~ 5.5 V
Operating Temperature
0°C ~ 105°C
Mounting Type
Surface Mount
Package / Case
24-QSOP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ADM1027ARQ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
ADM1027ARQZ
Manufacturer:
AD
Quantity:
8 852
Step 7
Determine T
T
measured temperature has dropped back below T
fan turns off. The premise for temperature hysteresis (T
is that without it, the fan would merely chatter, or cycle on and
off regularly, whenever the temperature is hovering about the
T
The T
needed for the system to cool down or heat up, as the fan is
turning on and off. Values of hysteresis are programmable in
the range 1rC to 15rC. Larger values of T
chattering on and off as previously described. The T
value is 4rC.
Hysteresis Registers
Reg. 0x6D Remote 1, Local Hysteresis Register
<7:4> = Remote 1 temperature hysteresis (default = 4rC)
<3:0> = Local temperature hysteresis (default = 4rC)
Reg. 0x6E Remote 2 Temperature Hysteresis Register
<7:4> = Remote 2 temperature hysteresis (default = 4rC)
HYST
MIN
setting.
HYST
is the amount of extra cooling a fan provides after the
value chosen will determine the amount of time
HYST
AMBIENT TEMP
Figure 36. The T
REMOTE 2 =
REMOTE 1 =
VRM TEMP
CPU TEMP
for Each Temperature Channel
100%
LOCAL =
0%
T
HYST
T
MIN
T
T
T
MIN
MIN
MIN
THERMAL CALIBRATION
THERMAL CALIBRATION
THERMAL CALIBRATION
HYST
Value Applies to Fan On/Off Hysteresis and THERM Hysteresis
T
RANGE
T
T
T
HYST
RANGE
RANGE
RANGE
T
THERM
prevent the fans
100%
100%
0%
100%
0%
0%
Rev. 3 | Page 35 of 56 | www.onsemi.com
MIN
HYST
before the
default
–35–
HYST
MUX
)
PWM
PWM
PWM
Note that in some applications it is required that the fans not
turn off below T
of Enhance Acoustics Register 1 (Reg. 0x62) allow the fans to
be turned off or kept spinning below T
on, the T
ture drops below T
Enhance Acoustics Register 1 (Reg. 0x62)
Bit 7 (MIN3) = 0, PWM3 is OFF (0% PWM duty cycle) when
temperature is below T
Bit 7 (MIN3) = 1, PWM3 runs at PWM3 minimum duty cycle
below T
Bit 6 (MIN2) = 0, PWM2 is OFF (0% PWM duty cycle) when
temperature is below T
Bit 6 (MIN2) = 1, PWM2 runs at PWM2 minimum duty cycle
below T
Bit 5 (MIN1) = 0, PWM1 is OFF (0% PWM duty cycle) when
temperature is below T
Bit 5 (MIN1) = 1, PWM1 runs at PWM1 minimum duty cycle
below T
MIN
MIN
MIN
TACHOMETERS 3
MEASUREMENT
ENHANCEMENT)
TACHOMETER 1
ENHANCEMENT)
TACHOMETER 2
ENHANCEMENT)
MEASUREMENT
MEASUREMENT
(ACOUSTIC
(ACOUSTIC
(ACOUSTIC
CONTROL
CONTROL
CONTROL
MIN
MIN
MIN
AND 4
RAMP
RAMP
RAMP
HYST
– T
– T
– T
value has no effect on the fan when the tempera-
HYST
HYST
HYST
MIN
MIN
GENERATOR
GENERATOR
GENERATOR
, but remain running at PWM
.
.
.
CONFIG
CONFIG
CONFIG
PWM
PWM
PWM
PWM
PWM
PWM
.
MIN
MIN
MIN
– T
– T
– T
HYST
HYST
HYST
PWM1
TACH1
PWM2
TACH2
PWM3
TACH3
.
.
.
MIN
. If the fans are always
ADM1027
MIN
. Bits <7:5>
CPU
FANSINK
FRONT
CHASSIS
REAR
CHASSIS