ADUM1201AR Analog Devices Inc, ADUM1201AR Datasheet - Page 16

• Manufacturer Part Number: ADUM1201AR
• Description: IC DIGITAL ISOLATOR 2CH 8-SOIC
• Manufacturer: Analog Devices Inc
• Series: iCoupler®r

Specifications of ADUM1201AR

• Inputs - Side 1/side 2: 1/1
• Number Of Channels: 2
• Isolation Rating: 2500Vrms
• Voltage - Supply: 2.7 V ~ 5.5 V
• Data Rate: 1Mbps
• Propagation Delay: 150ns
• Output Type: Logic
• Package / Case: 8-SOIC (3.9mm Width)
• Operating Temperature: -40°C ~ 105°C
• Operating Temperature (min): -40C
• Operating Temperature Classification: Industrial
• Operating Temperature (max): 105C
• Package Type: SOIC N
• Rad Hardened: No
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

ADuM1200/ADuM1201
Parameter
1
2
3
4
5
6
7
8
The supply current values are for both channels combined when running at identical data rates. Output supply current values are
present.
Figure 6 through Figure 8 for information on per-channel supply current as a function of data rate for unloaded and loaded
for total I
The minimum pulse width is the shortest pulse width at which the specified pulse-width distortion is guaran
The maximum data rate is the fastest data rate at which the specified pulse-width distortion is guaranteed.
t
measured from the 50% level of the rising edge of the V
t
load within the recommended operating conditions.
Codirectional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of
the isolation barrier. Opposing directional channel
inputs on opposing sides of the isolation barrier.
CM
that can be sustained while maintaining V
magnitude is the range over which the common mode is slewed.
Dynamic supply current is the incremental amount of supply current required for a 1 Mbps increase in the signal d
information on per-channel supply current as a function of da
calculating per-channel supply current for a given data rate.
PHL
PSK
ADuM120xWURZ
For All Models
H
propagation delay is measured from the 50% level of the falling edge of the V
is the magnitude of the worst-case difference in t
Pulse Width Distortion, |t
Propagation Delay Skew
Channel-to-Channel Matching
Minimum Pulse Width
Maximum Data Rate
Propagation Delay
Pulse Width Distortion, |t
Propagation Delay Skew
Channel-to-Channel Matching
Common-Mode Transient Immunity
Dynamic Supply Current per
Output Rise/Fall Time(10% to 90%)
Output Rise/Fall Time(10% to 90%)
Refresh Rate
is the maximum common-mode voltage slew rate that can be sustained while maintaining V
Change vs. Temperature
Codirectional Channels
Opposing Directional Channels
Change vs. Temperature
Codirectional Channels
Opposing Directional Channels
Logic High Output
Logic Low Output
Channel
Input
Output
The supp
DD1
and I
8
DD2
ly curre
supply currents as a function of data rate for ADuM1200W and ADuM1201W channel configurations.
4
nt associated with an individual channel operating at a given data rate can be calculated as described in the Power Co
7
3
7
2
PLH
PLH
5
5
6
6
− t
– t
PHL
PHL
|
|
4
4
6
6
O
< 0.8 V. The common-m
Symbol
PWD
t
t
t
t
PW
t
PWD
t
t
t
t
|CM
|CM
f
I
I
DDI (D)
DDO (D)
PSK
PSKCD
PSKOD
R
PHL
PSK
PSKCD
PSKOD
R
r
/t
/t
F
, t
F
H
L
|
-to-channel matching is the absolute value of the difference in propagation delays between any two channels with
|
PLH
PHL
and/or t
Ix
signal to the 50% level of the rising edge of the V
Min
25
20
25
25
ta rate for unloaded and loaded conditions. See the Power Consumption section for guidance on
PLH
that is measured between units at the same operating temperature, supply voltages, and output
ode voltage slew rates apply to both rising and falling common-mode voltage edges. The transient
Rev. H | Page 16 of 28
Ix
signal to the 50% level of the fallin
Typ
5
3.0
20
50
5
3.0
35
35
1.2
0.19
0.03
O
> 0.8 V
DD2
Max
3
3
22
3
22
40
50
15
3
15
Ox
. CM
teed.
signal.
L
is the maximum common-mode voltage slew rate
ata rate. See Figure 6 through F
g edge of the V
conditions. See Figure 9 through Figure 11
Unit
ns
ps/°C
ns
ns
ns
ns
ns
Mbps
ns
ns
ps/°C
ns
ns
ns
ns
kV/μs
kV/μs
Mbps
mA/
Mbps
mA/
Mbps
specified with no ou
Ox
signal. t
Test Conditions
C
V
transient magnitude = 800 V
V
transient magnitude = 800 V
L
Ix
Ix
= 15 pF, CMOS signal levels
= V
= V
nsumpti
DD1
DD1
PLH
, V
, V
propagation delay is
igure 8 for
DD2
DD2
on section
, V
, V
tput load
CM
CM
= 1000 V,
= 1000 V,
. See