MOC3033M Fairchild Optoelectronics Group, MOC3033M Datasheet
![OPTOCOUPLER TRIAC-OUT ZC 6-DIP](/photos/7/72/77281/moc3033m_sml.jpg)
MOC3033M
Specifications of MOC3033M
MOC3033-MQT
MOC3033-MQT
MOC3033QT
Available stocks
Related parts for MOC3033M
MOC3033M Summary of contents
Page 1
... MOC3031M, MOC3032M, MOC3033M, MOC3041M, MOC3042M, MOC3043M 6-Pin DIP Zero-Cross Optoisolators Triac Driver Output (250/400 Volt Peak) Features Simplifies logic control of 115 VAC power Zero voltage crossing dv/dt of 2000 V/µs typical, 1000 V/µs guaranteed VDE recognized (File # 94766), ordering option V (e.g., MOC3043VM) ...
Page 2
Absolute Maximum Ratings Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure ...
Page 3
... All devices are guaranteed to trigger operating I lies between max I F 5mA for MOC3033M & MOC3043M) and absolute max I 4. This is static dv/dt. See Figure 9 for test circuit. Commutating dv/ function of the load-driving thyristor(s) only. ©2005 Fairchild Semiconductor Corporation MOC303XM, MOC304XM Rev. 1.0 25° ...
Page 4
Safety and Insulation Ratings As per IEC 60747-5-2, this optocoupler is suitable for “safe electrical insulation” only within the safety limit data. Compliance with the safety ratings shall be ensured by means of protective circuits. Symbol Installation Classifications per DIN ...
Page 5
Typical Performance Curves Figure 1. LED Forward Voltage vs. Forward Current 1.6 1.5 1 1.0 0.9 0.8 0 LED ...
Page 6
Typical Performance Curves Figure Leakage in Inhibit State vs. Temperature DRM2 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 - AMBIENT TEMPERATURE ( C) A Figure 7. Holding Current, I 3.2 2.8 ...
Page 7
... LED current has been removed. The dv/dt is then decreased until the D.U.T. stops triggering. measured at this point and recorded. V max = 250 V APPLIED VOLTAGE WAVEFORM 0.63 V max 158 dv/ VOLTS the part, 5mA for the MOC3033M and MOC3043M, 10mA for HOT 115 VAC 0.01 LOAD NEUTRAL For highly inductive loads (power factor < ...
Page 8
... This optoisolator should not be used to drive a load directly intended trigger device only. ©2005 Fairchild Semiconductor Corporation MOC303XM, MOC304XM Rev. 1.0 SCR 180 4 R2 Figure 14. Inverse-Parallel SCR Driver Circuit (MOC3031M, MOC3032M, MOC3033M SCR 360 4 R2 Figure 15. Inverse-Parallel SCR Driver Circuit (MOC3041M, MOC3042M, MOC3043M) 8 ...
Page 9
Package Dimensions Through Hole 8.13–8. 6.10–6.60 Pin 5.08 (Max.) 0.25–0.36 3.28–3.53 0.38 (Min.) 2.54–3.81 2.54 (Bsc) (0.86) 0.41–0.51 1.02–1.78 0.76–1.14 Surface Mount 6.10–6.60 8.43–9.90 3.28–3.53 5.08 (Max.) 0.38 (Min.) Note: All dimensions in mm. ©2005 ...
Page 10
Ordering Information Option No option S SR2 SR2V Marking Information Definitions *Note – Parts that do not have the ‘V’ option (see definition 3 above) that are marked with date ...
Page 11
Carrier Tape Specification 4.5 0.20 0.30 21.0 0.1 0.1 MAX User Direction of Feed Reflow Profile 300 280 260 240 220 200 180 160 C 140 120 100 ©2005 Fairchild Semiconductor Corporation MOC303XM, MOC304XM ...
Page 12
TRADEMARKS The following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its gl o bal subsidiaries, and is not intended exhaustive list of all such trademarks. AccuPower F-PFS FRFET Auto-SPM Build it ...