20-101-0303 Rabbit Semiconductor, 20-101-0303 Datasheet - Page 22
20-101-0303
Manufacturer Part Number
20-101-0303
Description
SMARTSCREEN OP7100 W/TOUCHSCREEN
Manufacturer
Rabbit Semiconductor
Datasheet
1.101-0303.pdf
(126 pages)
Specifications of 20-101-0303
Display Type
STN - Super-Twisted Nematic
Viewing Area
121.00mm L x 91.00mm W
Backlight
CCFL - White
Dot Pitch
0.36mm x 0.36mm
Dot Pixels
320 x 240 (QVGA)
Interface
Serial
Product
Prototyping Accessories
Processor Type
Z180
Sram
128 KB
Flash
512 KB
Number Of I/os
16
Backup Battery
3 V Lithium Coin Type
Operating Voltage
10 V to 30 V
Power Consumption
4.5 W
Interface Type
Ethernet
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Display Mode
-
Dot Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
20-101-0303
20-101-303
20-101-303
316-1175
20-101-303
20-101-303
316-1175
- Current page: 22 of 126
- Download datasheet (780Kb)
Running Dynamic C
Double-click the Dynamic C icon to start the software. Note that the PC
attempts to communicate with the OP7100 each time Dynamic C is started.
No error messages are displayed once communication is established.
The communication rate, port, and protocol are all selected by choosing
Serial Options
OP7100 both set their baud rate automatically to match the communication
rate set on the host PC using Dynamic C (9600 bps, 19,200 bps, 28,800 bps,
or 57,600 bps). To begin, adjust the communications rate to 19,200 bps.
Make sure that the PC serial port used to connect the serial cable (COM1
or COM2) is the one selected in the Dynamic C
the 1-stop-bit protocol.
At this point, the LCD should be blank and the backlight should be off.
Once communication is established, load the sample program
DEFDEMOL.C
and run the program by pressing
menu.
The OP7100 should now alternately display the large font (17x × 35h) and
the small font (6w × 8h). The fonts should scroll across the display.
22 Getting Started
See Appendix A, “Troubleshooting,” if an error message such
as
Once the necessary changes have been made to establish
communication between the host PC and the OP7100, use the
Dynamic C shortcut
communication.
Compiling and running this sample program will overwrite the
demonstration program shown in Figure 2-3.
in the Dynamic C
Target Not Responding
from Dynamic C’s
SAMPLES\QVGA
<Ctrl Y>
F9
OPTIONS
or by selecting
or
to reset the controller and initiate
Communication Error
menu. The SIB and the
OPTIONS
subdirectory. Compile
Run
from the
menu. Select
Run
appears.
OP7100
Related parts for 20-101-0303
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY PROG OP670
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY ETH OP6700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2030
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BOARD ETH BL2010
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE OP6810 W/O ETH/MEM EXPANS
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2020
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2010 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2020 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD BL2500 44.2MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD FULL BL2000
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2110
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD 29.4MHZ BL2610
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
INTERFACE OP6800 512K FLASH&SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet: