FTLF1419P1BCL Finisar Corporation, FTLF1419P1BCL Datasheet
FTLF1419P1BCL
Specifications of FTLF1419P1BCL
Related parts for FTLF1419P1BCL
FTLF1419P1BCL Summary of contents
Page 1
... Fibre Channel as defined in FC-PI 13.0 free per Directive 2002/95/EC diagnostics functions are available via the 2-wire serial bus specified in the SFP MSA. PRODUCT SELECTION x © Finisar Corporation November 4, 2005 Rev. A FTLF1419P1xCL APPLICATIONS • 1.25Gb/s 1000Base-LX Ethernet • Dual Rate 1.06 / 2.125 Gb/s Fibre ...
Page 2
... LOS is open collector output. Should be pulled up with 4.7k – 10 kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. Towards Bezel Pinout of Connector Block on Host Board © Finisar Corporation November 4, 2005 Rev. A Name/Description <0.8V. DIS VeeT ...
Page 3
... Receiver sensitivity is compliant with power supply sinusoidal modulation 1.5 MHz up to specified value applied through the recommended power supply filtering network. 8. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ Δ and DJ. © Finisar Corporation November 4, 2005 Rev. A Symbol Min Typ Vcc -0.5 ...
Page 4
... Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ Δ and DJ. 6. Measured with conformance signals defined in FC-PI 13.0 specifications measured with 9dB extinction ratio. Measured with a PRBS 2 © Finisar Corporation November 4, 2005 Rev - ° 3.00 to 3.60 Volts Symbol ...
Page 5
... Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TÜV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request. © Finisar Corporation November 4, 2005 Rev. A Symbol ...
Page 6
... Note AN-2030. Digital diagnostics for the FTLF1419P1xCL are externally calibrated by default. Please note that evaluation board FDB-1018 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface. © Finisar Corporation November 4, 2005 Rev PROM that is accessible over a 2 PROM that are not write-protected ...
Page 7
... FTLF1419P1xCL Pluggable SFP Product Specification – November 2005 IX. Mechanical Specifications Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA) © Finisar Corporation November 4, 2005 Rev. A FTLF1419P1BCL Page 7 ...
Page 8
... FTLF1419P1xCL Pluggable SFP Product Specification – November 2005 © Finisar Corporation November 4, 2005 Rev. A FTLF1419P1WCL Page 8 ...
Page 9
... FTLF1419P1xCL Pluggable SFP Product Specification – November 2005 X. PCB Layout and Bezel Recommendations © Finisar Corporation November 4, 2005 Rev Page 9 ...
Page 10
... FTLF1419P1xCL Pluggable SFP Product Specification – November 2005 © Finisar Corporation November 4, 2005 Rev Page 10 ...
Page 11
... The FTLF1419P1xCL complies with this standard, except for the optical output power. See section IV for details. XII. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com © Finisar Corporation November 4, 2005 Rev Page 11 ...