IPM12C0A0S04FA Delta Electronics, IPM12C0A0S04FA Datasheet
IPM12C0A0S04FA
Specifications of IPM12C0A0S04FA
Available stocks
Related parts for IPM12C0A0S04FA
IPM12C0A0S04FA Summary of contents
Page 1
... The documentation and background information listed below is relevant to this evaluation to the procedure: ․ Applicative date sheets for IPM Series unit under evaluation. ․ Power Module Evaluation Board Schematic. ․ Power Module Evaluation Board Layout. ․ General Test and Safety Procedures. 1 Delta Electronics, Inc. ...
Page 2
Equipment Required ․ DC Power Supply 20A (Agilent 6574A 0 -60V/0 - 35A or equivalent). ․Oscilloscope (Tektronix TDS 460A or equivalent) 4 Channel 400 MHz, equipped with a x1 scope probe, a ...
Page 3
Connect one lead from the “+” lead of the power supply to the “20A” terminal of the first multimeter DMM1. Then connect one lead from the “Common” of the DMM1 to the “Vin” pin of the Evaluation Board. Set ...
Page 4
Tests Performed The following tests are performed at room temperature (+25 C). 6.1 Input Characteristics Input Voltage Range. Under-Voltage Locko No Load Input Current 6.2 O utput Characteristics Line Regulation. Load Regulation. Output Regulation . Output Voltage Se t-Point ...
Page 5
SW3 for the trim-down or trim-up setting of the Output Voltage. For IPM, if the converter requires a trim up, set SW3 to the Trim-up position. If the converter requires a trim down, set SW3 to ...
Page 6
Initial Power Up 1) Turn the power supply ON, set the current limit on power supply (refer to specification of either converter) and increase the input voltage (use DMM2 to monitor the voltage) until it reaches the desired value. ...
Page 7
Output Characteristics 8.2.1 Line Regulation Line Regulation Deviation is defined as the change in output voltage caused by varying the input voltage over a specif ied range while the output load and temperature remain constant. Test 1) Turn on ...
Page 8
Output Voltage Set-Point Adjustment Range (Trim) O utput Voltage Set-Point Adjustment can be carried out by using an external resistor or external voltage source to increase or decrease the output voltag th e data sheet for the detailed ...
Page 9
For I M04C series implement Trim-up by using an external resistor, R TRIM pin and groun d. For IPM04C0A0R06A, Please refer to the IPMR table for the desired Vout. The value of R can be calculated by ...
Page 10
Output Voltage Set-Point Adjustment by using an external voltage source For IPM12C series Output voltage of IPM12C is programmable while applying a voltage between the TRIM and GND pins. The following equation can be used to determine the value ...
Page 11
Dynamic Characteristics 8.3.1 Output Voltage Deviation Output Voltage Deviation is defined as the response of the converter to a sudden step change in the output load current. The output voltage deviation is characterized by two parameters: Maximum Output Voltage ...
Page 12
Test (Turn on the module by using the external switch) 1) Turn on the fan. 2) Turn on the input power supply and set it to the desired operating point. 3) Set channel 1 on the oscilloscope ...
Page 13
Use the following formulas to calculate the efficiency: Efficiency= (Pout/Pin) × 100(%) Pin = Iin × Vin Pout = Iout × Vout For IPM12C series The following graph shows the efficiency results of the IPM12C0A0R04A converter measured at different ...
Page 14
Appendix A- Evaluation Board Schematic 14 ...
Page 15
Appendix B - Evaluation Board Layout (Top View) 15 ...
Page 16
Appendix C - Evaluation Board Layout (Bottom View) CONTACT: www.delta.com.tw/dcdc USA: Telephone: East Coast: (888) 335 8201 West Coast: (888) 335 8208 Fax: (978) 656 3964 Email: DCDC@delta-corp.com WARRANTY Delta offers a two (2) year limited warranty. Complete warranty information ...