ST7MDT20J-TEB STMicroelectronics, ST7MDT20J-TEB Datasheet
ST7MDT20J-TEB
Specifications of ST7MDT20J-TEB
Related parts for ST7MDT20J-TEB
ST7MDT20J-TEB Summary of contents
Page 1
... ST7MDT20J-EMU3 Probe User Guide Ref: DOC-ST7MDT20J-EMU3 Release 2.3 March 2005 ...
Page 2
... Appendix A: EMC Conformity and Safety Requirements Please refer to information. USE IN LIFE SUPPORT DEVICES OR SYSTEMS MUST BE EXPRESSLY AUTHORIZED. STMicroelectronics PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF STMicroelectronics. As used herein: 1. Life support devices or systems are those ...
Page 3
Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4
... MCU or family of MCU’s. This allows you to emulate a range of ST7 MCUs with one EMU3 emulator. For this reason, the ST7MDT20J Target Emulation Board is delivered either as part of the ST7MDT20J-EMU3 emulator kit, or independently, in the ST7MDT20J-TEB kit. The ST7MDT20J-EMU3 emulator is designed to emulate MCUs in the ST72321, ST72324 and ST72344 families. ...
Page 5
... ST7MDT20J-EMU3 Probe User Guide The EMU3 probe connects to your application board via adapters, device adapters and socket or connectors, which are furnished as part of the emulator or TEB kit. Adapters (also called flex adapters), connect to the probe’s target emulation board. Depending on the package of the target device, they can be connected directly to a socket on your application board device adapter ...
Page 6
... ST7-EMU3 Emulator User Manual - set up instructions for your emulator ST72324B ST72F324 Datasheet or ST72321 Datasheet - includes debugging and programming information that is specific to these ST7 families. Because of the modularity of the EMU3 emulator, this guide is delivered with the following products: • ST7MDT20J-TEB • ST7MDT20J-EMU3 emulator 6/29 ST7MDT20J-EMU3 Probe User Guide ...
Page 7
... ST7-EMU3 Emulator User Manual ), as well as all of the probe accessories listed below. Owners of other versions of EMU3 emulators can configure them to emulate the ST72324 and ST72321 families with the ST7MDT20J-TEB kit. This kit includes the ST7MDT20J TEB (ref.: DB518) to install in the probe, as well as the connection accessories listed below (No. 2-5). ...
Page 8
... Delivery Checklist 8/29 (1) (2) (4) (a) (5) (a) Figure 2: ST7MDT20J-EMU3 Probe kit ST7MDT20J-EMU3 Probe User Guide (3) (b) (b) ...
Page 9
... MCU, The target MCUs that are emulated by the ST7MDT20J-EMU3 Probe exist in various microcontroller packages—four different packages in total. To connect the emulator to your application board, you must assemble/connect the flex adapter, adapters and/or sockets for the microcontroller package you are using ...
Page 10
... SDIP32 connector. Figure 4: Connecting flex adapter to TEB 10/29 Figure 3 . Figure 3: Opening the bottom of the probe , identify the TEB connectors you must use for your shows a the SDIP32 flex adapter (ref.: DB510) being inserted into SDIP42/TQFP44 connector ST7MDT20J-EMU3 Probe User Guide SDIP32 connector ...
Page 11
... ST7MDT20J-EMU3 Probe User Guide 3 Replace the bottom panel of the probe housing so that the flex adapter feeds through the slot provided. 4 Reconnect the probe to the ST Micro Connect box by connecting the two 80-pin flat cables to the ST MIcro Connect connection ports on the top face of the probe housing ...
Page 12
... Solder a SDIP42 socket onto your application board. 2 Align the pin 1 indicators on the SDIP42 connector of the DB513 flex adapter, then insert the into the socket on your application board as shown in Flex adapter Socket 12/29 ST7MDT20J-EMU3 Probe User Guide Application board Figure 5: SDIP42 connection scheme Figure 5 . Pin 1 indicators ...
Page 13
... ST7MDT20J-EMU3 Probe User Guide 3.3 TQFP44 (10 x 10) microcontroller package 1 Solder the Yamaichi TQFP44 socket onto your application board, according to the manufacturer’s instructions. Note: Put aside the cover provided with the Yamaichi TQFP44 socket. You can use it later to fasten an actual microcontroller into the socket in place of the emulator’s flex adapter. ...
Page 14
... Align the pin 1 indicators on the SDIP32 connector of the DB510 flex adapter, then insert the SDIP32 end of the DB510 flex adapter into the socket on your application board as shown in Flex adapter 14/29 Figure 7 . Socket Application board Figure 7: SDIP32 connection scheme ST7MDT20J-EMU3 Probe User Guide Pin 1 indicators ...
Page 15
... ST7MDT20J-EMU3 Probe User Guide 3.5 TQFP32 microcontroller package 1 Solder the TQFP32 male connector onto your application board. 2 Align the pin 1 indicators for the TQFP32 end of the DB522 flex adapter and the TQFP32 male connector on the application board. Then insert the pin of the ...
Page 16
... EMU3 TEB are described in this section. MCU In STVD7’s MCU Selection window, choose the MCU that you are using in your application. A complete and up-to-date listing of supported MCUs for your ST7MDT20J-EMU3 emulator is provided in the current version of the STVD7 Release Notes . Clock The Clock frequency options are summarized in ...
Page 17
... ST7MDT20J-EMU3 Probe User Guide CSS (Clock Security System) This option allows you to Enable or Disable the clock security system function (CSS) which includes the clock filter and the backup safe oscillator. When enabled, the selected OSCRANGE is used to determine the operating frequency range, and when the frequency is out of range, the clock source will be switched to the backup oscillator ...
Page 18
... If this option is set to No Reset, no chip reset will be performed. WDG (Watchdog) This option allows you to choose whether the watchdog timer is enabled by software or by hardware. Refer to the datasheet of your target ST7 MCU for more information on the watchdog timer. 18/29 ST7MDT20J-EMU3 Probe User Guide on page 20 for more ...
Page 19
... ST7MDT20J-EMU3 Probe User Guide 4.2 Emulator electrical characteristics This section details the specific electrical characteristics of the ST7MDT20J-EMU3 emulator. 4.2.1 Power follower characteristics The application power supply follower converts the application voltage V voltage within the range of 2.4 V and 5.5 V. The curve plotted on the graph below ...
Page 20
... The LVD option is always turned off in HALT/Active HALT mode, no matter what the selected VD option is. • The LVD thresholds for VDD rise and VDD fall are not compliant with the last version of the datasheet (revision 1.4) for the ST72(F)521/321/324 emulator chip. 20/29 ST7MDT20J-EMU3 Probe User Guide VD (Voltage detection) on page 17: ...
Page 21
... ST7MDT20J-EMU3 Probe User Guide APPENDIX A: EMC CONFORMITY AND SAFETY REQUIREMENTS This product respects the EMC requirements of the European guideline 89/336/ EEC under the following conditions: • Any tester, equipment, or tool used at any production step, or for any manipulation of semiconductor devices, must have its shield connected to ground. • ...
Page 22
... Figure 10 3 Remove the target emulation board that is currently in the probe by gripping the edge of the board and pulling it straight out (see safe and static-free for future use. 22/29 ST7MDT20J-EMU3 Probe User Guide Figure 3 on page 10. . Figure 10: Removing the TEB screws Figure 11 ...
Page 23
... ST7MDT20J-EMU3 Probe User Guide The board under the TEB – the Dedicated Emulation Board (DEB), should now be visible (see 4 Identify the top and bottom faces of the TEB you wish to install. The bottom face is distinguished by the presence of two or more flex cable connectors placed side by side ...
Page 24
... If this is the first time that you have installed a new TEB in your EMU3 probe, your emulator and probe firmware will be updated automatically by STVD7 when you start a debug session. For more information refer to your STVD7 User Manual . 24/29 ST7MDT20J-EMU3 Probe User Guide Figure 10 . Take care not to over-tighten the screws. Figure 12 on page 23 ...
Page 25
... Nov 2001 2.0 Jan 2002 2.1 Sep 2002 2.2 Mar 2005 2.3 Table 1: ST7MDT20J-EMU3 Probe User Guide Revision History Appendix C: Document Revision History Description • Updated Product Support – with spare parts information and preparing to call procedure • Updated Section 4.3 – ...
Page 26
... Complete documentation and ordering information for P/TQFP sockets from Yamaichi, Ironwood, CAB and Enplas are provided at the following Internet sites: www.yamaichi.de www.ironwoodelectronics.com www.cabgmbh.com www.enplas.com Connectors Complete documentation and ordering information for SAMTEC connectors is provided at www.samtec.com. 26/29 ST7MDT20J-EMU3 Probe User Guide Contact List provided ...
Page 27
... ST7MDT20J-EMU3 Probe User Guide Getting prepared before you call Collect the following information about the product before contacting ST or your distributor: 1 Name of the company where you purchased the product. 2 Date of purchase. 3 Order Code: Refer to the side your emulators box. The order code will depend on the region in which is was ordered (i ...
Page 28
... Germany + U.K. +44 162 889 0800 Japan +81 3 3280 4120 Hong-Kong +85 2 2861 5700 Sydney +61 2 9580 3811 Taipei + 2378 8088 28/29 ST7MDT20J-EMU3 Probe User Guide North America Mid West STMicroelectronics 1300 East Woodfield Road, Suite 410 Schaumburg, IL 60173 Phone: (847) 585-3000 ...
Page 29
... No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. ...