DM-COP8/44P National Semiconductor, DM-COP8/44P Datasheet - Page 46
DM-COP8/44P
Manufacturer Part Number
DM-COP8/44P
Description
CABLE FOR DEBUG MODULE 44-PLCC
Manufacturer
National Semiconductor
Datasheet
1.DM-COP820D.pdf
(254 pages)
Specifications of DM-COP8/44P
Accessory Type
44-PLCC Target Cable
For Use With/related Products
MetaLink Debug Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*DM-COP8/44P
- Current page: 46 of 254
- Download datasheet (2Mb)
COPSAx7 I/O structure minimizes external component requirements. Software-
switchable I/O enables designers to reconfigure the microcontroller's I/O functions with
a single instruction. Each individual I/O pin can be independently configured as an
output pin low, an output high, an input with high impedance or an input with a weak
pull-up device. A typical example is the use of I/O pins as the keyboard matrix input lines.
The input lines can be programmed with internal weak pull-ups so that the input lines
read logic high when the keys are all up. With a key closure, the corresponding input line
will read a logic zero since the weak pull-up can easily be overdriven. When the key is
released, the internal weak pull-up will pull the input line back to logic high. This
flexibility eliminates the need for external pull-up resistors. The High current options are
available for driving LEDs, motors and speakers. This flexibility helps to ensure a
cleaner design, with less external components and lower costs. Below is the general
description of all available pins.
V
CKI is the clock input. This can come from the Internal R/C oscillator, external, or a
crystal oscillator (in conjunction with CKO). See Oscillator Description section.
RESET is the master reset input. See Reset description section.
The device contains four bidirectional 8-bit I/O ports (C, G, L and F), where each
individual bit may be independently configured as an input (Schmitt trigger inputs on
ports L and G), output or TRI-STATE under program control. Three data memory
address locations are allocated for each of these I/O ports. Each I/O port has two
associated 8-bit memory mapped registers, the CONFIGURATION register and the
output DATA register. A memory mapped address is also reserved for the input pins of
each I/O port. (See the memory map for the various addresses associated with the I/O
ports.) Figure 2-4 shows the I/O port configurations. The DATA and CONFIGURATION
registers allow for each port bit to be individually configured under software control as
shown below:
Port L is an 8-bit I/O port. All L-pins have Schmitt triggers on the inputs.
Port L supports the Multi-Input Wake Up feature on all eight pins. The 16-pin device
does not have a full complement of Port L pins. The unavailable pins are not terminated.
A read operation these unterminated pins will return unpredictable values. To minimize
current drain, the unavailable pins must be programmed as outputs.
2-8
CC
and GND are the power supply pins. All V
COP8SAx7 MICROCONTROLLER
CONFIGURATION
Register
0
0
1
1
Register
DATA
0
1
0
1
CC
Hi-Z Input
(TRI-STATE Output)
Input with Weak Pull-Up
Push-Pull Zero Output
Push-Pull One Output
and GND pins must be connected.
Port Set-Up
Related parts for DM-COP8/44P
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
CABLE FOR DEBUG MODULE 20-DIP
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
CABLE FOR DEBUG MODULE 28-DIP
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
SWITCH ROCKER DPDT BLK
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER POWER DPST 10A QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH PWR ROCKER DPST SNAP-IN
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER DPST SNAP-IN QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER SPST ILUM 10A/125V
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER DPDT W/MRK QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER POWER DPST 3A QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER ILLUM 10A GRN
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER DPST SNAP-IN QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER POWER DPST 3A QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
MINI ROCKER DPDT BLK
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER POWER SPST 3A QC
Manufacturer:
C&K Components
Datasheet: