OM6290 NXP Semiconductors, OM6290 Datasheet - Page 65

• Manufacturer Part Number: OM6290
• Description: DEMO BOARD LCD GRAPHIC DRIVER
• Manufacturer: NXP Semiconductors

Specifications of OM6290

• Main Purpose: Displays, LCD Controller
• Embedded: Yes, MCU, 16/32-Bit
• Utilized Ic / Part: PCF2119, PCF8531, PCF8576
• Primary Attributes: Character, Graphic and Segment LCD Drivers
• Secondary Attributes: JTAG, I²C, UART & USB Interfaces
• Description/function: Demo Board
• Interface Type: USB, I2C, JTAG, UART
• Data Bus Width: 4 bit, 8 bit, 16 bit
• Operating Voltage: 1.8 V to 5.5 V
• For Use With/related Products: PCF8576DT, PCF2119S, PCF8531
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-4703

NXP Semiconductors
Table 42.
Table 43.
PCF2119X
Product data sheet
Step
22
23
Step
1
2
3
4
5
6
7
8
9
10
11
12 to 15
Instruction
RS
Return_home
0
I
I
slave address for write
SA6 SA5 SA4 SA3 SA2 SA1 SA0 R/W Ack
0
send a control byte for Function_set
CO
0
Function_set
DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack
0
Display_ctl
DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack
0
Entry_mode_set
DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack
0
I
slave address for write
SA6 SA5 SA4 SA3 SA2 SA1 SA0 R/W Ack
0
send a control byte for Write_data
CO
0
Write_data to DDRAM
DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack P
0
Write_data to DDRAM
DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack PH
0
2
2
2
C-bus byte
C-bus start
C-bus start
8-bit operation, 2-line display example; using external reset (character set ‘A’)
Example of I
16.12 I
R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Display
0
1
RS
0
0
0
0
1
RS
1
1
1
0
1
0
0
1
0
0
1
0
0
0
0
A control byte is required with most commands (see
2
2
C-bus operation; 1-line display (using external reset, assuming pin SA0 = V
C-bus operation, 1-line display
0
1
0
0
X
0
0
1
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
1
:
:
0
1
0
0
0
1
1
1
0
0
0
0
All information provided in this document is subject to legal disclaimers.
0
0
0
0
0
1
1
0
0
0
0
0
Rev. 9 — 14 April 2011
0
0
0
0
0
0
0
0
0
0
0
0
1
1
Ack
1
1
1
1
1
Ack
1
1
1
0
Display
PHILIP
:
PHILIPS
MICROCOM
Operation
initialized; no display appears
during the acknowledge cycle SDA will be
pulled-down by the PCF2119x
control byte sets RS for following data bytes
selects 1-line display and V
pulse during acknowledge cycle starts
execution of instruction
turns on display and cursor; entire display
shows character code 20h (blank in
ASCII-like character sets)
sets mode to increment the address by 1
and to shift the cursor to the right at the time
of write to the DDRAM or CGRAM; display
is not shifted
for writing data to DDRAM, RS must be set
to 1; therefore a control byte is needed
writes ‘P’; the DDRAM has been selected at
power-on; the cursor is incremented by 1
and shifted to the right
writes ‘H’
writes ‘ILIP’
Table
Operation
returns both display and cursor to the
original position (address 0)
43).
…continued
LCD controllers/drivers
PCF2119x
© NXP B.V. 2011. All rights reserved.
LCD
SS
)
[1]
= V
0
; SCL
65 of 83