CY8CKIT-006 Cypress Semiconductor Corp, CY8CKIT-006 Datasheet - Page 14

• Manufacturer Part Number: CY8CKIT-006
• Description: KIT DEV PSOC3 LCD SEGMENT
• Manufacturer: Cypress Semiconductor Corp
• Series: PSOC™ 3r

Specifications of CY8CKIT-006

• Main Purpose: Displays, LCD Display
• Embedded: Yes, MCU, 32-Bit
• Primary Attributes: 448 addressable segments
• Secondary Attributes: Configurable LCD pin selection
• Description/function: Evaluation Kit
• Interface Type: USB
• Backlighting: No Backlighting
• Data Bus Width: 8 bit, 16 bit, 32 bit
• Maximum Operating Temperature: + 50 C
• Minimum Operating Temperature: 0 C
• Number Of Segments: 7
• Operating Supply Voltage: 12 V
• Operating Voltage: 3.3 V
• Pixel Format: 16 x 28
• Product: Display Modules
• Software: Software Included
• Touch Panel: No Touch Panel
• For Use With/related Products: PSoC 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Utilized Ic / Part: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 428-2994

Kit Operation
3.4.5
3.5
14
■
■
■
■
■
■
■
The alarm time is set for the HH:MM selected and the SS is set to 00 by the code. The RTC Alarm
interrupt is enabled.
When setting the alarm, pressing RET exits the SetAlm sub menu immediately without saving the
alarm information
2:Alarm
This sub menu allows to turn the alarm on/off. Upon entering, either "AlarmOFF" or "AlarmON" is
displayed based on the current alarm on/off settings.
■
■
■
In the clock mode, alarm symbol is displayed if alarm is enabled. When the time reaches the set
alarm time, the buzzer present on the board will beep. The buzzer will sound for up to 2-minutes
before automatically shutting off. If the buzzer is shut off automatically, then the alarm remains on
and starts the buzzer the next time the alarm time is reached again. You can manually turn off the
alarm in three ways:
1. Press the sleep pushbutton from any state.
2. Press any CapSense button (for example, SEL) from any state.
3. Reopen the 2:Alarm sub menu item and set the Alarm state to "OFF".
CONTRAST
The project is designed for 3.3V operation and this bias level is set in the SegLCD component of the
design. The CONTRAST sub menu allows the selection of a value in the range 0 to 10 to set the bias
higher or lower to allow viewing the contrast effects.
Press SEL to enter the CONTRAST sub menu. The project displays the current contrast setting on
the matrix display in the format "Level= X", where X is a value in the range 0 to 10. Press "+" or "-" to
increment or decrement the value displayed. The progress bar at the bottom displays the contrast
level in graphical format.
Pressing SEL or RET stores the contrast level in the persistent memory and project returns to the
CONTRAST sub menu.
Press SEL to advance to the next M position (M2).
Press "+" or "-" to select '0' - '9'.
Press SEL to advance to the 16-segment display character.
Press "+' or "-" to select AM or PM.
Press "+" or "-" to select 'A' - 'P'. The 14-segment display character shows 'M'.
Press SEL to enter the alarm settings. "Push SEL" is prompted on the matrix display.
Press SEL to exit the "SetTim" sub menu.
Press "+" and "-" button to select "AlarmOFF" or "Alarm ON".
Press SEL to enter the ON/OFF alarm state. "PushSEL" is prompted on the matrix display.
Press SEL to exit the Alarm set sub menu.
CY8CKIT-006 PSoC 3 LCD Segment Drive Evaluation Kit Guide, Doc. # 001-52798 Rev. *C
[+] Feedback