STEVAL-PSQ001V1 STMicroelectronics, STEVAL-PSQ001V1 Datasheet - Page 33

• Manufacturer Part Number: STEVAL-PSQ001V1
• Description: BOARD EVAL BASED ON PM6680A
• Manufacturer: STMicroelectronics
• Type: Other Power Managementr

Specifications of STEVAL-PSQ001V1

• Design Resources: STEVAL-PSQ001V1 Gerber Files STEVAL-PSQ001V1 Schematic STEVAL-PSQ001V1 Bill of Material
• Main Purpose: DC/DC, Step Down with LDO
• Outputs And Type: 6, Non-Isolated
• Voltage - Output: 0.9 ~ 2.5 V, 1 ~ 3.3 V, 2x 3.3 V, 2.5 V, 5 V
• Current - Output: 4A, 2A, 800mA, 400mA, 400mA, 150mA
• Voltage - Input: 5 ~ 36V
• Regulator Topology: Buck
• Frequency - Switching: 200kHz, 300kHz
• Board Type: Fully Populated
• Utilized Ic / Part: PM6680A
• Input Voltage: 5 V to 36 V
• Output Voltage: 1 V to 3.3 V
• Product: Power Management Modules
• Silicon Manufacturer: ST Micro
• Silicon Core Number: PM6680A
• Kit Application Type: Power Management
• Application Sub Type: Power Supply
• Kit Contents: Board
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With/related Products: PM6680A
• Other names: 497-6425; STEVAL-PSQ001V1

PM6680A
9.5
Power MOSFETS
Logic-level MOSFETs are recommended, since low side and high side gate drivers are
powered by LDO5. Their breakdown voltage VBR
In notebook applications, power management efficiency is a high level requirement. The
power dissipation on the power switches becomes an important factor in switching
selections. Losses of high-side and low-side MOSFETs depend on their working conditions.
The power dissipation of the high-side MOSFET is given by:
Equation 18
Maximum conduction losses are approximately:
Equation 19
where RDSon is the drain-source on resistance of the high side MOSFET.
Switching losses are approximately:
Equation 20
where t
As general rule, high side MOSFETs with low gate charge are recommended, in order to
minimize driver losses.
Below there is a list of possible choices for the high side MOSFET.
Table 13.
The power dissipation of the low side MOSFET is given by:
Equation 21
Maximum conduction losses occur at the maximum input voltage:
Manufacturer
P
switching
on
and t
ST
High side MOSFET manufacturer
=
off
V
IN
are the switching times of the turn
×
I (
LOAD
STS5NF60L
P
conduction
(max)
Type
P
DHighSide
2
−
P
∆
=
2
DLowSide
I
R
L
)
DSon
=
×
P
t
on
conduction
×
Gate charge (nC)
=
×
V
V
P
f
IN
OUT
sw
conduction
min
DSS
+
25
+
×
on
V
P
I
IN
LOAD
must be higher than V
switching
and turn
×
I (
(max)
LOAD
(max)
off
2
Rated reverse voltage (V)
phases of the MOSFET.
2
+
∆
Design guidelines
2
I
L
)
×
INmax
60
t
off
×
.
f
sw
33/48