AS1323-30 EB austriamicrosystems, AS1323-30 EB Datasheet
AS1323-30 EB
Specifications of AS1323-30 EB
Related parts for AS1323-30 EB
AS1323-30 EB Summary of contents
Page 1
... µ General Description The AS1323 high-efficiency step-up DC-DC converter was designed specifically for single-cell, battery-pow- ered devices where lowest quiescent current and high efficiency are essential. The compact device is available in three fixed-voltage variations and is perfect for a wide variety of applications where extremely-low quiescent currents and very-small form factors are critical ...
Page 2
... Shutdown mode. 3 SHDNN 1 = Normal operating mode. Output. This pin also supplies bootstrap power to the device. 4 VOUT Inductor Connection. This pin is connected to the internal N-channel MOSFET switch 5 LX drain and P-channel synchronous rectifier drain. www.austriamicrosystems.com/DC-DC_Step-Up/AS1323 VBATT AS1323 VSS 2 SHDNN 3 4 VOUT Description Revision 1. ...
Page 3
... Table 3. Absolute Maximum Ratings Parameter VBATT, SHDNN VSS Maximum Current VOUT, LX Thermal Resistance Θ JA Electro-Static Discharge Operating Temperature Range Storage Temperature Range Junction Temperature Package Body Temperature www.austriamicrosystems.com/DC-DC_Step-Up/AS1323 may cause permanent damage to the device. These are stress ratings only, Min Max Units -0 207.4 º ...
Page 4
... SQC (Statistical Quality Control) methods. www.austriamicrosystems.com/DC-DC_Step-Up/AS1323 = V , SHDNN = OUT OUT(NOM) OUT LOAD Condition T = 25ºC AMB T = 25ºC, AMB R = 100Ω LOAD AS1323-27 AS1323-30 AS1323- 1.5V; BATT I = 45mA LOAD Programmed at 400mA V = 1.5V BATT OUT 3.3V 25ºC AMB OUT V = 1.5V 25ºC BATT AMB ...
Page 5
... Output Current (m A) Figure 7. Output Voltage vs. Temperature 3.32 3.315 No Load 3.31 3.305 3 10mA LOAD 3.295 3. 30mA LOAD 3.285 3.28 -50 - Tem perature (°C) www.austriamicrosystems.com/DC-DC_Step-Up/AS1323 = 10mA 1.5V; unless otherwise specified. LOAD BATT = 3.3V Figure 4. Efficiency vs. Output Current; V OUT 1. 1. 0.95V 0.1 100 = 2.7V Figure 6 ...
Page 6
... OUT 3.04 3. 10mA OUT 3 2. 30mA OUT 2.96 2.94 2.92 2.9 0.75 1 1.25 1.5 Input Voltage (V) www.austriamicrosystems.com/DC-DC_Step-Up/AS1323 Figure 10. Shutdown Current vs. Temperature 1000 100 10 1 0.1 1.6 1.7 -50 -25 Figure 12. Output Voltage vs. Input Voltage 2.7V OUT 2.78 2.76 2.74 2.72 2.7 2.68 2 ...
Page 7
... Figure 15. Output Current vs. Input Voltage 110 100 3.0V OUT 3.3V OUT OUT 0.75 1 1.25 1.5 Input Voltage (V) Figure 17. Switching Waveform; V OUT 200µs/Div www.austriamicrosystems.com/DC-DC_Step-Up/AS1323 Figure 16. Switching Waveform 2.7V 1. 3.0V Figure 18. Switching Waveform; V Revision 1.05 = 2.7V OUT 200µs/Div = 3.3V OUT 200µs/Div ...
Page 8
... Datasheet - Detailed Description The AS1323 is a compact, high-efficiency, step-up DC-DC converter guaranteed to start up with voltages as low as 0.95V, and operate with an input voltage down to 0.75V. Consuming only 1.6µA of quiescent current, the device includes an integrated synchronous rectifier that eliminates the need for an external diode and improves overall effi- ...
Page 9
... Datasheet - Application Information Figure 20. Typical Application Inductor Selection The control scheme of the AS1323 allows for a wide range if inductor values. A 10µH inductor should be sufficient for most applications (see Figure 20). Smaller inductance values typically offer smaller physical size for a given series resistance, allowing the smallest over- all circuit dimensions ...
Page 10
... PC Board Layout Considerations The AS1323 has been specially designed to be tolerant to PC board parasitic inductances and resistances. However, to achieve maximum efficiency a careful PC board layout and component selection is vital. Note: For the optimal performance the IC’s VSS and the ground leads of the input and output capacitors must be kept less than 5mm apart using a ground plane ...
Page 11
... The package top can be smaller than the package bottom. Dimensions D and E1 are determined at the outer- most extremes of the plastic body exclusive of mold flash, tie bar burrs, gate burrs, and interlead flash, but include any mistmatches between the top of the package body and the bottom. D and E1 are determined at datum H. www.austriamicrosystems.com/DC-DC_Step-Up/AS1323 Max Notes Symbol 1 ...
Page 12
... AS1323 Datasheet - Tape and Reel Pin1 Orientation Figure 22. Tape&Reel Pin1 Orientation Top, Through View TSOT23-5 www.austriamicrosystems.com/DC-DC_Step-Up/AS1323 User direction of feed TSOT23-5 TSOT23-5 TSOT23-5 Revision 1. ...
Page 13
... Note: All products are RoHS compliant and Pb-free. Buy our products or get free samples online at ICdirect: For further information and requests, please contact us or find your local distributor at www.austriamicrosystems.com/DC-DC_Step-Up/AS1323 Table 5. Description 1.6µA Quiescent Current, Single Cell, DC-DC Step-up Converter 1.6µ ...
Page 14
... No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services. Contact Information Headquarters austriamicrosystems AG Tobelbaderstrasse 30 A-8141 Unterpremstaetten, Austria Tel: +43 (0) 3136 500 0 Fax: +43 (0) 3136 525 01 For Sales Offices, Distributors and Representatives, please visit: http://www.austriamicrosystems.com/contact www.austriamicrosystems.com/DC-DC_Step-Up/AS1323 Revision 1. ...