AD9510/PCB Analog Devices Inc, AD9510/PCB Datasheet - Page 39
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9510/PCB
Manufacturer Part Number
AD9510/PCB
Description
IC CLOCK DISTRIB PLL 64LFCSP
Manufacturer
Analog Devices Inc
Datasheet
1.AD9510BCPZ-REEL7.pdf
(60 pages)
Specifications of AD9510/PCB
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Phase offsets may be related to degrees by calculating the phase
step for a particular divide ratio:
Using some of the same examples,
DELAY BLOCK
OUT5 and OUT6 (LVDS/CMOS) include an analog delay
element that can be programmed (Register 34h to Register 3Ah)
to give variable time delays (Δt) in the clock signal passing
through that output.
The amount of delay that can be used is determined by the
frequency of the clock being delayed. The amount of delay can
approach one-half cycle of the clock period. For example, for a
10 MHz clock, the delay can extend to the full 10 ns maximum
of which the delay element is capable. However, for a 100 MHz
clock (with 50% duty cycle), the maximum delay is less than
5 ns (or half of the period).
OUT5 and OUT6 allow a full-scale delay in the range 1 ns to
10 ns. The full-scale delay is selected by choosing a combination
of ramp current and the number of capacitors by writing the
appropriate values into Register 35h and Register 39h. There are
32 fine delay settings for each full scale, set by Register 36h and
Register 3Ah.
CLOCK INPUT
Unique Phase Offsets Are Phase = 0, 1, 2, 3, 4, 5, 6
DIV = 18
Unique Phase Offsets Are Phase = 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10,
Phase Step = 360°/(Divide Ratio) = 360°/DIV
DIV = 4
Phase Step = 360°/4 = 90°
Unique Phase Offsets in Degrees Are Phase = 0°, 90°,
DIV = 7
Phase Step = 360°/7 = 51.43°
Unique Phase Offsets in Degrees Are Phase = 0°, 51.43°,
11, 12, 13, 14, 15, 16, 17
180°, 270°
102.86°, 154.29°, 205.71°, 257.15°, 308.57°
OUT5
OUT6 ONLY
∅SELECT
÷
Figure 40. Analog Delay (OUT5 andOUT6)
N
FULL-SCALE: 1ns TO 10ns
FINE DELAY ADJUST
(32 STEPS)
Δ
T
CMOS
LVDS
OUTPUT
DRIVER
Rev. A | Page 39 of 60
This path adds some jitter greater than that specified for the
nondelay outputs. This means that the delay function should be
used primarily for clocking digital chips, such as FPGA, ASIC,
DUC, and DDC, rather than for data converters. The jitter is
higher for long full scales (~10 ns). This is because the delay
block uses a ramp and trip points to create the variable delay. A
longer ramp means more noise might be introduced.
Calculating the Delay
The following values and equations are used to calculate the
delay of the delay block.
Value of Ramp Current Control Bits (Register 35h or Register 39h
<2:0>) = Iramp_bits
I
No. of Caps = No. of 0s + 1 in Ramp Control Capacitor
(Register 35h or Register 39h <5:3>), that is, 101 = 1 + 1 = 2; 110
= 2; 100 = 2 + 1 = 3; 001 = 2 + 1 = 3; 111 = 0 + 1 = 1)
Delay_Range (ns) = 200 × ((No. of Caps + 3)/(I
Delay_Full_Scale (ns) = Delay_Range + Offset
Fine_Adj = Value of Delay Fine Adjust (Register 36h or
Register 3Ah <5:1>), that is, 11111 = 31
Delay (ns) = Offset + Delay_Range × Fine_adj × (1/31)
OUTPUTS
The AD9510 offers three different output level choices:
LVPECL, LVDS, and CMOS. OUT0 to OUT3 are LVPECL only.
OUT4 to OUT7 can be selected as either LVDS or CMOS. Each
output can be enabled or turned off as needed to save power.
The simplified equivalent circuit of the LVPECL outputs is
shown in Figure 41.
Offset
RAMP
(μA) = 200 × (Iramp_bits + 1)
( )
ns
Figure 41. LVPECL Output Simplified Equivalent Circuit
=
0.34
+
(
1600
GND
−
I
RAMP
)
×
3.3V
10
−
4
+
⎛
⎜
⎜
⎝
No.
OUT
OUTB
of
I
RAMP
RAMP
Caps
)) × 1.3286
AD9510
−
1
⎞
× ⎟ ⎟
⎠
6