TCFGA1A156M8R Rohm Semiconductor, TCFGA1A156M8R Datasheet - Page 4

• Manufacturer Part Number: TCFGA1A156M8R
• Description: CAP TANTALUM 15UF 10V 20% SMD
• Manufacturer: Rohm Semiconductor
• Series: TCFGr
• Type: Moldedr

Specifications of TCFGA1A156M8R

• Capacitance: 15µF
• Voltage - Rated: 10V
• Tolerance: ±20%
• Esr (equivalent Series Resistance): 3.500 Ohm
• Operating Temperature: -55°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 1206 (3216 Metric)
• Size / Dimension: 0.126" L x 0.063" W (3.20mm x 1.60mm)
• Height: 0.063" (1.60mm)
• Manufacturer Size Code: A
• Features: Fail Safe with Built-in Fuse
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Spacing: -
• Other names: 511-1480-2

○
TCFG Series A Case
c
www.rohm.com
2010 ROHM Co., Ltd. All rights reserved.
Temperature
Stability
Surge
Voltage
Loading at
High
temperature
Terminal
Strength
Adhesiveness
Item
Temp.
ΔC / C
tanδ
L.C
Temp.
ΔC / C
tanδ
L.C
Temp.
ΔC / C
tanδ
L.C
Appearance
L.C
ΔC / C
tanδ
Appearance
L.C
ΔC / C
tanδ
Capacitance
Appearance There should be no significant abnormality.
−55 °C
Within 0/−12%of initial value
Shall be satisfied the voltage on "Standard list"
+85 °C
Within +10/0%of initial value
Shall be satisfied the voltage on "Standard list"
Less than 1000% of initial limit
+125 °C
Within +15/0%of initial value
Shall be satisfied the voltage on "Standard list"
Less than 1250% of initial limit
There should be no significant abnormality.
The indications should be clear.
Less than initial limit
Within
Less than initial limit
There should be no significant abnormality.
The indications should be clear.
Less than initial limit
TCFGA1A226M8R : Within
TCFGA0J476M8R : Within
TCFGA0G686M8R : Within
Others
Less than initial limit
The measured value should be stable.
The terminal should not come off.
±
10%of initial value
Performance
: Within
−
±
±
±
±
15% of initial value
15% of initial value
15% of initial value
10% of initial value
4/7
As per 4.29 JIS C 5101-1
As per 4.13 JIS C 5101-3
As per 4.26 JIS C 5101-1
As per 4.14 JIS C 5101-3
Apply the specified surge voltage via the serial
resistance of 1kΩ every 5±0.5min.
for 30±5 s. each time in the atmospheric condition
of 85±2°C.
Repeat this procedure 1,000 times.
After the specimens, leave it at room temperature
for over 24h and then measure the sample.
As per 4.23 JIS C 5101-1
As per 4.15 JIS C 5101-3
After applying the rated voltage for 2000+72/0h
without discontinuation via the serial resistance
of 3 Ω or less at a temperature of 85 ± 2 °C , leave
the sample at room temperature/humidity for
over 24h and measure the value.
As per 4.35 JIS C 5101-1
As per 4.9 JIS C 5101-3
A force is applied to the terminal until it bends
to 1mm and by a prescribed tool maintain the
condition for 5s. (See the figure below.)
As per 4.34 JIS C 5101-1
As per 4.8 JIS C 5101-3
Apply force of 5N in the two directions shown
in the figure below for 10 ± 1s after mounting
the terminal on a circuit board.
Thickness 1.6mm
(based on JIS C5101-1 and JIS C5101-3)
Test conditions
50
45
R230
product
20
45
F (Apply force)
a circuit board
(Unit : mm)
1
Apply force
2010.01 - Rev.G
Data Sheet