ADL5306 Analog Devices, Inc., ADL5306 Datasheet
ADL5306
Related parts for ADL5306
ADL5306 Summary of contents
Page 1
... REF level at low currents can be addressed by using a buffer amplifier to realize low-pass filters three poles. The ADL5306 is available in a 16-lead LFCSP package and is specified for operation from–40°C to +85°C. ∗ Protected by US Patents 4,604,532 and 5,519,308; other patents pending. ...
Page 2
... ADL5306 TABLE OF CONTENTS Specifications..................................................................................... 3 Absolute Maximum Ratings............................................................ 4 Pin Configuration and Pin Function Descriptions...................... 5 Typical Performance Characteristics ............................................. 6 General Structure.............................................................................. 9 Theory............................................................................................ 9 Managing Intercept and Slope .................................................. 10 REVISION HISTORY Rev. 0: Initial Version Response Time and Noise Considerations ............................. 10 Applications..................................................................................... 11 Using a Negative Supply ............................................................ 11 Characterization Methods ........................................................ 12 Evaluation Board ............................................................................ 14 Outline Dimensions ...
Page 3
... L Load current < GAIN = 1 0 4.8 V output swing VPOS (Pin 8); VNEG (Pin 6) ) ≤ – ≤ – REF Rev Page ADL5306 1 1 Min Typ Max Unit 100n 100µ 100n 100µ A 0.46 0.5 0.54 V 0.015 mV/° ...
Page 4
... ADL5306 ABSOLUTE MAXIMUM RATINGS Table 2. ADL5306 Absolute Maximum Ratings Parameter Supply Voltage V – Input Current Internal Power Dissipation θ JA Maximum Junction Temperature Operating Temperature Range Storage Temperature Range Lead Temperature Range (Soldering 60 sec) Stresses above those listed under Absolute Maximum Ratings Rating may cause permanent damage to the device ...
Page 5
... Figure 2. 16-Lead Leadframe Chip Scale Package (LFCSP) . REF . Usually connected to photodiode anode such that photocurrent flows PD . This pin is usually grounded; for details of usage, see the Applications section. N – ≤ Rev Page VOUT SCAL BFIN VLOG ADL5306 ...
Page 6
... ADL5306 TYPICAL PERFORMANCE CHARACTERISTICS ( 200 kΩ 25°C, unless otherwise noted REF A 1 –40°C, 0°C, +25°C, +70°C, +85° 1.0 0.8 0.6 0.4 0.2 0 10n 100n 1µ 10µ I (A) PD Figure 3. V vs. I for Multiple Temperatures LOG PD 1 –40°C, 0°C, +25°C, +70°C, +85°C ...
Page 7
... TO 10µA: = 5µs, RISE t < 1µs FALL t 10µA TO 100µA: = 1µs, RISE t < 1µs FALL 100 120 140 TIME (µs) Figure 14. Pulse Response REF OUT ADL5306 1m 03727-0-012 PD 160 180 03727-0-013 160 180 03727-0-014 ...
Page 8
... ADL5306 10 5 100nA 0 –5 –10 –15 –20 –25 –30 –35 –40 100 1k 10k 100k 1M FREQUENCY (Hz) Figure 15. Small-Signal AC Response (5% Sine Modulation), from for I in Decade Steps from 100nA 0 –5 –10 –15 –20 –25 –30 –35 –40 100 ...
Page 9
... V, one fifth of the 2.5 V reference voltage appearing on Pin VREF. The resistance at the VSUM pin is nominally 16 kΩ; this voltage is not intended as a general bias source. The ADL5306 also supports the use of an optional negative supply voltage Pin VNEG. When V N negative, VSUM may be connected to ground ...
Page 10
... For more details, see and the AD8304 Data Sheet. P RESPONSE TIME AND NOISE CONSIDERATIONS The response time and output noise of the ADL5306 are fundamentally a function of the signal current I currents, the bandwidth is proportional to I frequency voltage-noise spectral density is a function of I increases for small values of I bandwidth performance of translinear log amps, see the AD8304 Data Sheet ...
Page 11
... APPLICATIONS The ADL5306 is easy to use in optical supervisory systems and in similar situations where a wide-ranging current converted to its logarithmic equivalent (i.e., represented in decibel terms). Basic connections for measuring a single current input are shown in Figure 22, which includes various nonessential components, as will be explained. VPOS +5V NC ...
Page 12
... INPT and IREF signal current. For example, it may be convenient to utilize a forward-biased junction voltage of about 0 Schottky barrier voltage of a little over 0.5 V. With the summing node at ground, the ADL5306 may now be used as a voltage-input log amp, at either the numerator input INPT or the denominator input IREF by inserting a suitably scaled resistor from the voltage source to the relevant pin ...
Page 13
... CELL 03727-0-027 Rev Page ADL5306 TDS5104 CH A 9213 COMM COMM COMM COMM VOUT NC 1 SCAL VREF 2 200kΩ ADL5306 3 IREF BFIN R1 4 INPT VLOG VSUM VNEG VNEG VPOS 50kΩ 1kΩ 1kΩ 1nF 1nF Measurement ...
Page 14
... SMA connector labeled INPT style packaged photodiode can be used in place of the INPT SMA for optical interfacing. By removing R1 and adding a 0 Ω short for R5, a second current can be applied to the IREF input (also SMA) for evaluating the ADL5306 in log-ratio applications. SC Style Photodiode Rev Page ...
Page 15
... VPOS OPEN OPEN AGND 0.01 µ F VOUT VREF C5 0.1 µ F VSUM AGND VPOS VLOG P1 Figure 31. Component Side Silkscreen Rev Page ADL5306 R10 VOUT OPEN R14 VOUT 0 Ω OPEN R8 VLOG OPEN R11 VLOG 0 Ω 03727-0-029 ...
Page 16
... Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. ORDERING GUIDE ADL5306 Products Temperature Package 2 ADL5306ACP –40°C to +85°C ADL5306ACP-R2 – ...