AMP04F Analog Devices, AMP04F Datasheet
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AMP04F
Available stocks
Related parts for AMP04F
AMP04F Summary of contents
Page 1
... AMP04 to high impedance transducers and other signal sources. *Protected by U.S. Patent No. 5,075,633. REV. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices ...
Page 2
... 100 4 – + – + Sink Source –2– AMP04E AMP04F Typ Max Min Typ Max 30 150 300 300 600 3 6 0.5 1 ...
Page 3
... AMP04F Typ Max Min Typ Max 270 270 1.5 1.5 0.7 0.7 300 300 550 700 700 850 850 AMP04E AMP04F Typ Max Min Typ Max 80 400 600 600 900 ...
Page 4
... C unless otherwise noted Conditions IOS OOS 3 100 G = 1000 – 100 –4– AMP04E AMP04F Min Typ Max Min Typ 0.2 0.5 0.4 0.75 0.8 1 1000 1 0.005 0.005 0.015 0.015 0.025 0.025 30 50 +13 +13.4 +13 +12 ...
Page 5
... JA socket for cerdip, P-DIP, and LCC packages; soldered in circuit board for SOIC package. Model AMP04EP AMP04ES AMP04FP AMP04FS AMP04FS-REEL AMP04FS-REEL7 AMP04GBC REV. A Symbol Conditions G = 1000 PSRR 4 ...
Page 6
AMP04 APPLICATIONS Common-Mode Rejection The purpose of the instrumentation amplifier is to amplify the difference between the two input signals while ignoring offset and noise voltages common to both inputs. One way of judging the device’s ability to reject this ...
Page 7
Programming the Gain The gain of the AMP04 is programmed by the user by selecting a single external resistor—R : GAIN Gain = 100 k /R The output voltage is then defined as the differential input volt- age times the ...
Page 8
AMP04 Compensating for Input and Output Errors To achieve optimal performance, the user needs to take into account a number of error sources found in instrumentation amplifiers. These consist primarily of input and output offset voltages and leakage currents. The ...
Page 9
Figure 7c Low-Pass Filtered Output Power Supply Considerations In dual supply applications (for example the input is connected to a low resistance source less than 100 , a large current ...
Page 10
AMP04 APPLICATION CIRCUITS Low Power Precision Single Supply RTD Amplifier Figure 11 shows a linearized RTD amplifier that is powered off a single +5 volt supply. However, the circuit will work volts without modification. The RTD is ...
Page 11
Calibration is simple and easy with the NULL adjusted first, followed by SPAN adjust. The entire circuit can be remotely placed, and powered from the 4-20 mA 2-wire loop. 4-20 mA Loop Receiver At the ...
Page 12
AMP04 120 BASED ON 300 UNITS 3 RUNS 100 –200 –160 –120 –80 – INPUT OFFSET VOLTAGE – V Figure 16. Input Offset (V ) Distribution @ +5 V IOS 120 100 80 ...
Page 13
TCV – OOS Figure 22. Output Offset Drift (TCV @ +5 V 5.0 4.8 4 100k L 4.4 4 10k ...
Page 14
AMP04 100 –10 –20 100 1k 10k FREQUENCY – Hz Figure 28. Closed-Loop Voltage Gain vs. Frequency 120 100 G = 100 ...
Page 15
VOLTAGE GAIN – G Figure 34. Voltage Noise Density vs. Gain 140 120 100 100 FREQUENCY – Hz Figure 36. Voltage Noise Density vs. Frequency 1200 1000 ...
Page 16
AMP04 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 8-Lead Plastic DIP (N- 0.280 (7.11) 0.240 (6.10 0.070 (1.77) 0.045 (1.15) 0.430 (10.92) 0.325 (8.25) 0.300 (7.62) 0.348 (8.84) 0.015 0.210 (0.381) TYP (5.33) MAX 0.130 ...