MAX7501 Maxim, MAX7501 Datasheet
MAX7501
Available stocks
Related parts for MAX7501
MAX7501 Summary of contents
Page 1
... The MAX7500 features three address select lines, while the MAX7501 and MAX7502 feature two address select lines and a RESET input. The MAX7500/MAX7501/ MAX7502s’ 3.0V to 5.5V supply voltage range, low 250µ ...
Page 2
... Note 3: Human Body Model, 100pF discharged through a 1.5k resistor. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability ...
Page 3
... START Condition Setup Time Data Setup Time Data Hold Time Maximum Receive SCL/SDA Rise Time Minimum Receive SCL/SDA Rise Time Maximum Receive SCL/SDA Fall Time Minimum Receive SCL/SDA Fall Time Transmit SDA Fall Time Pulse Width of Suppressed Spike SDA Time Low for Reset of Serial ...
Page 4
... Positive Supply Voltage Input. Bypass to GND with a 0.1µF bypass capacitor. alarm (OS) trip thresholds, and configure other charac- teristics. The MAX7500 features three address select lines (A0, A1, A2) while the MAX7501 and MAX7502 feature two address select lines (A0, A1) and a RESET input. The MAX7500/MAX7501/MAX7502 operate from +3.0V to +5.5V supply voltages of and consume 250µ ...
Page 5
... The MAX7500 has eight dif- ferent slave addresses available; therefore, a maximum of eight MAX7500 devices can share the same bus. The MAX7501/MAX7502 each have four different slave addresses available. BIT 2 BIT 1 ...
Page 6
Digital Temperature Sensors and Thermal Watchdog with Bus Lockup Protection 2 Figure 2. I C-Compatible Timing Diagram (Write) 6 _______________________________________________________________________________________ ...
Page 7
Digital Temperature Sensors and Thermal Watchdog with Bus Lockup Protection 2 Figure 3. I C-Compatible Timing Diagram (Read) _______________________________________________________________________________________ 7 ...
Page 8
... Positive X = Don’t care. Register Descriptions The MAX7500/MAX7501/MAX7502 have an internal pn- junction-based temperature sensor whose analog out- put is converted to digital form using a 9-bit sigma-delta ADC. The measured temperature and tem- perature configurations are controlled by the tempera- ture, configuration and T ...
Page 9
... OS deasserted only after performing a read operation. Set bit D0, the shutdown bit, to zero for normal opera- tion. Set bit shut down the MAX7500/ MAX7501/MAX7502 internal blocks, dropping the sup- 2 ply current to 3µA. The I C interface remains active as long as the shutdown bit is set. The T configuration registers can still be written to and read from while in shutdown ...
Page 10
... When the bus timeout is active, the minimum serial clock frequency is limited to 6Hz. The RESET input on the MAX7501/MAX7502 provides a way to reset the I their initial POR values. To reset, apply a low pulse with a duration of at least 1µs to the RESET input. ...
Page 11
... SDA and SCL lines to further help filter noise and ring- ing proves to be necessary placed in series with the SCL line, placed as close as possible to SCL. This 5k 10pF stray capacitance of the MAX7500/MAX7501/ MAX7502 provide a 6MHz to 12MHz lowpass filter, which is sufficient filtering in most cases. (the ...
Page 12
... Digital Temperature Sensors and Thermal Watchdog with Bus Lockup Protection (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages 0.50–0.1 0.6–0.1 1 0.6–0.1 D TOP VIEW FRONT VIEW ...
Page 13
... A1 FRONT VIEW Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13 © ...