ATTINY2313V-10MU Atmel, ATTINY2313V-10MU Datasheet - Page 26

• Manufacturer Part Number: ATTINY2313V-10MU
• Description: 10MHZ MLF IND TEMP GREEN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY2313V-10MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-MLF®, QFN
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: SPI/UART/USI
• Maximum Clock Frequency: 10 MHz
• Number Of Programmable I/os: 18
• Number Of Timers: 2
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• For Use With: ATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: Q2312268B

Oscillator Calibration
Register – OSCCAL
26
ATtiny2313
When this Oscillator is selected, start-up times are determined by the SUT Fuses as shown in
Table
Table 7. Start-up times for the internal calibrated RC Oscillator clock selection
Note:
• Bits 6..0 – CAL6..0: Oscillator Calibration Value
Writing the calibration byte to this address will trim the internal Oscillator to remove process vari-
ations from the Oscillator frequency. This is done automatically during Chip Reset. When
OSCCAL is zero, the lowest available frequency is chosen. Writing non-zero values to this regis-
ter will increase the frequency of the internal Oscillator. Writing 0x7F to the register gives the
highest available frequency. The calibrated Oscillator is used to time EEPROM and Flash
access. If EEPROM or Flash is written, do not calibrate to more than 10% above the nominal fre-
quency. Otherwise, the EEPROM or Flash write may fail. Note that the Oscillator is intended for
calibration to 8.0/4.0 MHz. Tuning to other values is not guaranteed, as indicated in
Avoid changing the calibration value in large steps when calibrating the Calibrated Internal RC
Oscillator to ensure stable operation of the MCU. A variation in frequency of more than 2% from
one cycle to the next can lead to unpredictable behavior. Changes in OSCCAL should not
exceed 0x20 for each calibration.
Table 8. Internal RC Oscillator Frequency Range.
Bit
Read/Write
Initial Value
SUT1..0
OSCCAL Value
10
00
01
11
(1)
7.
0x3F
0x7F
0x00
1. The device is shipped with this option selected.
Start-up Time from Power-
down and Power-save
R
7
–
Min Frequency in Percentage of
6 CK
6 CK
6 CK
CAL6
R/W
6
Nominal Frequency
CAL5
R/W
100%
5
50%
75%
Device Specific Calibration Value
CAL4
R/W
4
Additional Delay from
Reset (V
Reserved
14CK + 4.1 ms
14CK + 65 ms
CAL3
R/W
3
14CK
CC
= 5.0V)
Max Frequency in Percentage of
CAL2
R/W
2
Nominal Frequency
CAL1
R/W
Recommended Usage
BOD enabled
Fast rising power
Slowly rising power
1
100%
150%
200%
CAL0
R/W
0
OSCCAL
2543L–AVR–08/10
Table
8.