STM32F102R8T6 STMicroelectronics, STM32F102R8T6 Datasheet - Page 44

• Manufacturer Part Number: STM32F102R8T6
• Description: MCU ARM 32BIT 64KB FLASH 64-LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F102R8T6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 48MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 51
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Processor Series: STM32F102x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 10 KB
• Interface Type: I2C/SPI/USART/USB
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 51
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWARM, EWARM-BL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ST-LINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 12-bit
• For Use With: 497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-8311

Electrical characteristics
5.3.9
5.3.10
44/69
Table 26.
1. Based on characterization, not tested in production.
2. Take care of using the appropriate multiplier factors so as to have PLL input clock values compatible with
Memory characteristics
Flash memory
The characteristics are given at T
Table 27.
1. Guaranteed by design, not tested in production.
Table 28.
1. Based on characterization not tested in production.
EMC characteristics
Susceptibility tests are performed on a sample basis during device characterization.
t
Jitter
Symbol
LOCK
Symbol
N
t
t
ERASE
the range defined by f
V
RET
t
END
t
I
Symbol
prog
ME
DD
prog
Endurance
Data retention
16-bit programming time
Page (1 KB) erase time
Mass erase time
Supply current
Programming voltage
PLL characteristics (continued)
Flash memory characteristics
Flash memory endurance and data retention
PLL lock time
Cycle-to-cycle jitter
Parameter
Parameter
PLL_OUT
.
Parameter
Doc ID 15056 Rev 3
A
= –40 to 85 °C unless otherwise specified.
T
A
Read mode
f
wait states, V
Write / Erase modes
f
3.3 V
Power-down mode / Halt,
V
HCLK
HCLK
= 85 °C, 1000 cycles
DD
T
T
T
A
A
A
= 3.0 to 3.6 V
Conditions
–40 to +85 °C
= 48 MHz with 2
= 48 MHz, V
–40 to +85 °C
–40 to +85 °C
Conditions
DD
= 3.3 V
DD
Min
=
(1)
STM32F102x8, STM32F102xB
Min
30
10
Min
40
20
20
(1)
2
Value
(1)
Typ
Value
Typ
52.5
Typ
Max
200
300
Max
Max
(1)
3.6
70
40
40
20
50
5
(1)
kcycles
Years
Unit
Unit
µs
ps
Unit
mA
mA
ms
ms
µA
µs
V