DSPIC30F5016-30I/PT Microchip Technology, DSPIC30F5016-30I/PT Datasheet
DSPIC30F5016-30I/PT
Specifications of DSPIC30F5016-30I/PT
Available stocks
Related parts for DSPIC30F5016-30I/PT
DSPIC30F5016-30I/PT Summary of contents
Page 1
... Microchip Technology Inc. dsPIC30F5015/5016 Data Sheet High-Performance, 16-bit Digital Signal Controllers DS70149D ...
Page 2
... PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total Endurance, UNI/O, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 3
... All DSP instructions single cycle • ±16-bit single-cycle shift © 2008 Microchip Technology Inc. dsPIC30F5015/5016 Peripheral Features: • High-current sink/source I/O pins: 25 mA/25 mA • Timer module with programmable prescaler: - Five 16-bit timers/counters; optionally pair 16-bit timers into 32-bit timer modules • ...
Page 4
... Program SRAM Device Pins Mem. Bytes/ Bytes Instructions dsPIC30F5015 64 66K/22K 2048 dsPIC30F5016 80 66K/22K 2048 DS70149D-page 4 CMOS Technology: • Low-power, high-speed Flash technology • Wide operating voltage range (2.5V to 5.5V) • Industrial and Extended temperature ranges • Low power consumption Output Motor ...
Page 5
... SCK2/CN8/RG6 6 SDI2/CN9/RG7 7 SDO2/CN10/RG8 8 MCLR 9 SS2/CN11/RG9 FLTA/INT1/RE8 13 FLTB/INT2/RE9 14 AN5/QEB/CN7/RB5 15 AN4/QEA/CN6/RB4 16 AN3/INDX/CN5/RB3 17 AN2/SS1/CN4/RB2 18 PGC/EMUC/AN1/CN3/RB1 19 PGD/EMUD/AN0/CN2/RB0 20 . © 2008 Microchip Technology Inc. dsPIC30F5015/5016 dsPIC30F5016 EMUC1/SOSCO/T1CK/CN0/RC14 EMUD1/SOSCI/CN1/RC13 EMUC2/OC1/RD0 IC4/RD11 IC3/RD10 IC2/RD9 IC1/RD8 INT4/RA15 INT3/RA14 V SS OSC2/CLKO/RC15 OSC1/CLKI V DD SCL/RG2 SDA/RG3 EMUC3/SCK1/INT0/RF6 SDI1/RF7 EMUD3/SDO1/RF8 U1RX/RF2 U1TX/RF3 DS70149D-page 5 ...
Page 6
... PWM4L/RE6 2 PWM4H/RE7 3 SCK2/CN8/RG6 4 SDI2/CN9/RG7 5 SDO2/CN10/RG8 6 MCLR 7 SS2/CN11/RG9 AN5/QEB/CN7/RB5 11 AN4/QEA/CN6/RB4 12 AN3/INDX/CN5/RB3 13 AN2/SS1/CN4/RB2 14 AN1/V -/CN3/RB1 15 REF AN0/V +/CN2/RB0 16 REF DS70149D-page 6 48 EMUC1/SOSCO/T1CK/CN0/RC14 47 EMUD1/SOSCI/T4CK/CN1/RC13 46 EMUC2/OC1/RD0 45 IC4/INT4/RD11 44 IC3/INT3/RD10 43 IC2/FLTB/INT2/RD9 42 IC1/FLTA/INT1/RD8 41 V dsPIC30F5015 SS 40 OSC2/CLKO/RC15 39 OSC1/CLKI SCL/RG2 36 SDA/RG3 35 EMUC3/SCK1/INT0/RF6 34 U1RX/SDI1/RF2 33 EMUD3/U1TX/SDO1/RF3 © 2008 Microchip Technology Inc. ...
Page 7
... When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are using. Customer Notification System Register on our web site at www.microchip.com to receive the most current information on all of our products. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 DS70149D-page 7 ...
Page 8
... NOTES: DS70149D-page 8 © 2008 Microchip Technology Inc. ...
Page 9
... DSTEMP. Figure 1 block diagram of the DSTEMP device. Following the block diagram, Table 1-2 provides a brief description of the device I/O pinout and the functions that are multiplexed to the port pins on the DSTEMP. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 DS70149D-page 9 ...
Page 10
... AN15/CN12/RB15 PORTB EMUD1/SOSCI/T4CK/CN1/RC13 EMUC1/SOSCO/T1CK/CN0/RC14 OSC2/CLKO/RC15 PORTC EMUC2/OC1/RD0 EMUD2/OC2/RD1 OC3/RD2 OC4/RD3 CN13/RD4 CN14/RD5 CN15/RD6 UPDN/CN16/RD7 IC1/FLTA/INT1/RD8 IC2/FLTB/INT2/RD9 IC3/INT3/RD10 IC4/INT4/RD11 PORTD PWM1L/RE0 PWM1H/RE1 PWM2L/RE2 PWM2H/RE3 PWM3L/RE4 PWM3H/RE5 PWM4L/RE6 PWM4H/RE7 PORTE C1RX/RF0 C1TX/RF1 U1RX/SDI1/RF2 EMUD3/U1TX/SDO1/RF3 CN17/RF4 CN18/RF5 EMUC3/SCK1/INT0/RF6 PORTF © 2008 Microchip Technology Inc. ...
Page 11
... Legend: CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels I = Input © 2008 Microchip Technology Inc. dsPIC30F5015/5016 Description Analog input channels. AN0 and AN1 are also used for device programming data and clock inputs, respectively. Positive supply for analog module. This pin must be connected at all times. ...
Page 12
... Timer4 external clock input. UART1 Receive. UART1 Transmit. Positive supply for logic and I/O pins. Ground reference for logic and I/O pins. Analog Voltage Reference (High) input. Analog Voltage Reference (Low) input. Analog = Analog input O = Output P = Power 2 C™ © 2008 Microchip Technology Inc. ...
Page 13
... FIGURE 1-2: dsPIC30F5016 BLOCK DIAGRAM Y Data Bus Interrupt PSV & Table Controller Data Access 8 24 Control Block 24 24 PCH PCU Program Counter Stack Address Latch Control Control Logic Program Memory (66 Kbytes) Data EEPROM (1 Kbyte) 16 Data Latch ROM Latch Instruction Decode & ...
Page 14
... DSTEMP. Multiple functions may exist on one port pin. When multiplexing occurs, the peripheral module’s functional requirements may force an over- ride of the data direction of the port pin. TABLE 1-2: I/O PIN DESCRIPTIONS FOR dsPIC30F5016 Pin Buffer Pin Name Type ...
Page 15
... TABLE 1-2: I/O PIN DESCRIPTIONS FOR dsPIC30F5016 (CONTINUED) Pin Buffer Pin Name Type Type MCLR I/P ST OCFA I ST OCFB I ST OC1-OC4 O — OSC1 I ST/CMOS OSC2 I/O — PGD I/O ST PGC I ST RA9-RA10 I/O ST RA14-RA15 I/O ST RB0-RB15 I/O ST RC1 I/O ST RC3 I/O ...
Page 16
... NOTES: DS70149D-page 16 © 2008 Microchip Technology Inc. ...
Page 17
... Each data word consists of 2 bytes, and most instructions can address data either as words or bytes. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 There are two methods of accessing data stored in program memory: • The upper 32 Kbytes of data space memory can be ...
Page 18
... The upper byte of the SR register contains the DSP Adder/Subtracter Status bits, the DO Loop Active bit (DA) and the Digit Carry (DC) Status bit. 2.2.3 PROGRAM COUNTER The Program Counter is 23 bits wide. Bit 0 is always clear. Therefore, the PC can address instruction words. © 2008 Microchip Technology Inc. ...
Page 19
... DSP ACCA Accumulators ACCB PC22 0 7 TABPAG TBLPAG Data Table Page Address 7 0 PSVPAG PSVPAG OAB SAB DA SRH © 2008 Microchip Technology Inc. dsPIC30F5015/5016 D15 D0 W0/WREG W10 W11 W12/DSP Offset W13/DSP Write Back W14/Frame Pointer W15/Stack Pointer SPLIM AD15 AD31 PC0 ...
Page 20
... Signed divide: Wm/Wn → W0; Rem → W1 Unsigned divide: Wm/Wn → W0; Rem → block diagram of the DSP engine is shown in Figure 2-2. TABLE 2-2: Instruction CLR ED EDAC MAC MOVSAC MPY MPY.N MSC DSP INSTRUCTION SUMMARY Algebraic Operation change © 2008 Microchip Technology Inc. ...
Page 21
... FIGURE 2-2: DSP ENGINE BLOCK DIAGRAM 40 Carry/Borrow Out Carry/Borrow In © 2008 Microchip Technology Inc. dsPIC30F5015/5016 40-bit Accumulator A 40-bit Accumulator B Saturate Adder Negate Barrel 16 Shifter 40 Sign-Extend 17-bit Multiplier/Scaler 16 16 To/From W Array Round u Logic Zero Backfill DS70149D-page 21 ...
Page 22
... OVBTE) in the INTCON1 register (refer to Section 5.0 “Interrupts”) is set. This allows the user to take immediate action, for example, to correct system gain. trap when set and the © 2008 Microchip Technology Inc. ...
Page 23
... No saturation operation is performed and the accumulator is allowed to overflow (destroying its sign). If the COVTE bit in the INTCON1 register is set, a catastrophic overflow can initiate a trap exception. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 2.4.2.2 Accumulator ‘Write Back’ The MAC class of instructions (with the exception of MPY, MPY ...
Page 24
... The barrel shifter is 40 bits wide, thereby obtaining a 40-bit result for DSP shift operations and a 16-bit result for MCU shift operations. Data from the X bus is presented to the barrel shifter between bit positions for right shifts, and bit positions for left shifts. © 2008 Microchip Technology Inc. ...
Page 25
... TBLPAG<7> to determine user or configuration space access. In TABLE 3-1: “Program Space Address Construction”, bit 23 allows access to the Device ID, the User ID and the Configuration bits. Otherwise, bit 23 is always clear. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 FIGURE 3-1: PROGRAM SPACE MEMORY MAP FOR ...
Page 26
... Note: Program Space Visibility cannot be used to access bits <23:16> word in program memory. DS70149D-page 26 Program Space Address <23> <22:16> 0 TBLPAG<7:0> TBLPAG<7:0> 0 PSVPAG<7:0> 23 bits Program Counter Select bits 15 bits EA 8 bits 16 bits 24-bit EA <15> <14:1> <0> PC<22:1> 0 Data EA<15:0> Data EA<15:0> Data EA<14:0> 0 Byte Select © 2008 Microchip Technology Inc. ...
Page 27
... Program Memory ‘Phantom’ Byte (Read as ‘0’). © 2008 Microchip Technology Inc. dsPIC30F5015/5016 A set of table instructions are provided to move byte or word-sized data to and from program space. 1. TBLRDL: Table Read Low Word: Read the least significant word of the program address ...
Page 28
... Execution prior to exiting the loop due to an Reference interrupt - Execution upon re-entering the loop after an interrupt is serviced • Any other iteration of the REPEAT loop will allow the instruction, accessing data using PSV, to execute in a single cycle © 2008 Microchip Technology Inc. ...
Page 29
... The data space memory is split into two blocks, X and Y data space. A key element of this architecture is that Y space is a subset of X space, and is fully contained within X space. In order to provide an apparent linear addressing space, X and Y spaces have contiguous addresses. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 0x0000 (1) PSVPAG 0x00 ...
Page 30
... Memory 0xFFFF DS70149D-page 30 16 bits MSB LSB SFR Space X Data RAM (X) Y Data RAM (Y) Unimplemented ≈ Unimplemented ≈ X Data Unimplemented (X) LSB Address 0x0000 0x07FE 0x0800 8 Kbyte Near 0x0BFE Data 0x0C00 Space 0x0FFE 0x1000 0x1FFE 0x8000 0xFFFE © 2008 Microchip Technology Inc. ...
Page 31
... FIGURE 3-7: DATA SPACE FOR MCU AND DSP (MAC CLASS) INSTRUCTIONS EXAMPLE SFR SPACE (Y SPACE) Non-MAC Class Ops (Read/Write) MAC Class Ops (Write) Indirect EA using any W © 2008 Microchip Technology Inc. dsPIC30F5015/5016 SFR SPACE UNUSED Y SPACE UNUSED UNUSED MAC Class Ops Read-Only ...
Page 32
... FIGURE 3-8: 15 0x0000 Byte 1 0001 0x0000 Byte 3 0003 Byte 5 0x0000 0005 backward compatibility with DATA ALIGNMENT MSB LSB 0000 Byte 0 Byte 2 0002 Byte 4 0004 © 2008 Microchip Technology Inc. ...
Page 33
... Note push during exception processing will concatenate the SRL register to the MSB of the PC prior to the push. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 There is a Stack Pointer Limit register (SPLIM) associ- ated with the Stack Pointer. SPLIM is uninitialized at Reset the case for the Stack Pointer, SPLIM<0> ...
Page 34
TABLE 3-3: CORE REGISTER MAP Address SFR Name Bit 15 Bit 14 Bit 13 Bit 12 (Home) W0 0000 W1 0002 W2 0004 W3 0006 W4 0008 W5 000A W6 000C W7 000E W8 0010 W9 0012 W10 0014 ...
Page 35
TABLE 3-3: CORE REGISTER MAP (CONTINUED) Address SFR Name Bit 15 Bit 14 Bit 13 Bit 12 (Home) MODCON 0046 XMODEN YMODEN — XMODSRT 0048 XMODEND 004A YMODSRT 004C YMODEND 004E XBREV 0050 BREN DISICNT 0052 — — Legend: ...
Page 36
... NOTES: DS70149D-page 36 © 2008 Microchip Technology Inc. ...
Page 37
... Register Indirect Register Indirect Post-Modified Register Indirect Pre-Modified Register Indirect with Register Offset The sum of Wn and Wb forms the EA. Register Indirect with Literal Offset © 2008 Microchip Technology Inc. dsPIC30F5015/5016 4.1.1 FILE REGISTER INSTRUCTIONS Most file register instructions use a 13-bit address field (f) to directly address data present in the first 8192 bytes of data memory (near data space) ...
Page 38
... The only exception to the usage restrictions is for buffers which have a power-of-2 length. As these buffers satisfy the start and end address criteria, they may operate in a Bidirectional mode, (i.e., address boundary checks will be performed on both the lower and upper address boundaries). © 2008 Microchip Technology Inc. ...
Page 39
... MODULO ADDRESSING OPERATION EXAMPLE Byte Address 0x1100 0x1163 Start Addr = 0x1100 End Addr = 0x1163 Length = 0x0032 words © 2008 Microchip Technology Inc. dsPIC30F5015/5016 4.2.2 W ADDRESS REGISTER SELECTION The Modulo and Bit-Reversed Addressing Control register, MODCON<15:0>, contains enable flags, as well register field to specify the W Address registers ...
Page 40
... W register that has been designated as the Bit-Reversed Pointer. Sequential Address Bit Locations Swapped Left-to-Right Around Center of Binary Value Bit-Reversed Address Pivot Point XB = 0x0008 for a 16-word Bit-Reversed Buffer N bytes, should not be enabled © 2008 Microchip Technology Inc. ...
Page 41
... TABLE 4-2: BIT-REVERSED ADDRESS SEQUENCE (16-ENTRY) Normal Address TABLE 4-3: BIT-REVERSED ADDRESS MODIFIER VALUES FOR XBREV REGISTER Buffer Size (Words) 4096 2048 1024 512 256 128 © 2008 Microchip Technology Inc. dsPIC30F5015/5016 Bit-Reversed Address Decimal XB<14:0> Bit-Reversed Address Modifier Value A0 Decimal ...
Page 42
... NOTES: DS70149D-page 42 © 2008 Microchip Technology Inc. ...
Page 43
... The current CPU priority level is explicitly stored in the IPL bits. IPL<3> is present in the CORCON register, whereas IPL<2:0> are present in the STATUS register (SR) in the processor core. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 • INTCON1<15:0>, INTCON2<15:0> Global interrupt control functions are derived from these two registers ...
Page 44
... INT4 – External Interrupt Reserved 39 47 PWM – PWM Period Match 40 48 QEI – QEI Interrupt 41 49 Reserved 42 50 Reserved 43 51 FLTA – PWM Fault FLTB – PWM Fault B 45-53 53-61 Reserved Lowest Natural Order Priority © 2008 Microchip Technology Inc. ...
Page 45
... A momentary dip in the power supply to the device has been detected which may result in malfunction. • Trap Lockout: Occurrence of multiple trap conditions simultaneously will cause a Reset. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 5.3 Traps Traps can be considered as non-maskable interrupts indicating a software or hardware error, which adhere to a predefined priority, as shown in Figure 5-1 ...
Page 46
... Address Error Trap Vector Math Error Trap Vector Reserved Vector AIVT Reserved Vector Reserved Vector Interrupt 0 Vector Interrupt 1 Vector — — — Interrupt 52 Vector Interrupt 53 Vector © 2008 Microchip Technology Inc. 0x000000 0x000002 0x000004 0x000014 0x00007E 0x000080 0x000082 0x000084 0x000094 0x0000FE ...
Page 47
... The RETFIE (Return from Interrupt) instruction will unstack the program counter and STATUS registers to return the processor to its state prior to the interrupt sequence. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 5.5 Alternate Vector Table In program memory, the Interrupt Vector Table (IVT) is followed by the Alternate Interrupt Vector Table (AIVT), as shown in Figure 5-1 ...
Page 48
TABLE 5-2: INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC30F5015 SFR ADR Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Name INTCON1 0080 NSTDIS — — — — INTCON2 0082 ALTIVT DISI — — — IFS0 0084 CNIF MI2CIF SI2CIF ...
Page 49
... TABLE 5-3: INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC30F5016 SFR ADR Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Name INTCON1 0080 NSTDIS — — — — INTCON2 0082 ALTIVT — — — — IFS0 0084 CNIF MI2CIF SI2CIF NVMIF ADIF IFS1 0086 — — ...
Page 50
... NOTES: DS70149D-page 50 © 2008 Microchip Technology Inc. ...
Page 51
... Addressing Using Table Instruction User/Configuration Space Select © 2008 Microchip Technology Inc. dsPIC30F5015/5016 manufacture boards with unprogrammed devices, and then program the microcontroller just before shipping the product. This also allows the most recent firmware or a custom firmware to be programmed. 6.2 ...
Page 52
... NVMKEY register. Refer to Section 6.6 “Programming Operations” for further details. Note: The user can also directly write to the NVMADR and NVMADRU registers to specify a program memory address for erasing or programming. © 2008 Microchip Technology Inc. ...
Page 53
... MOV #0xAA,W1 MOV W1 NVMKEY , BSET NVMCON,#WR NOP NOP © 2008 Microchip Technology Inc. dsPIC30F5015/5016 4. Write 32 instruction words of data from data RAM “image” into the program Flash write latches. 5. Program 32 instruction words into program Flash. a) Set up NVMCON register for multi-word, program Flash, program, and set WREN bit ...
Page 54
... Write PM low word into program latch ; Write PM high byte into program latch ; Block all interrupts with priority <7 ; for next 5 instructions ; Write the 0x55 key ; ; Write the 0xAA key ; Start the erase sequence ; Insert two NOPs after the erase ; command is asserted © 2008 Microchip Technology Inc. ...
Page 55
TABLE 6-1: NVM REGISTER MAP File Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 NVMCON 0760 WR WREN WRERR NVMADR 0762 NVMADRU 0764 — — — NVMKEY 0766 — — — ...
Page 56
... NOTES: DS70149D-page 56 © 2008 Microchip Technology Inc. ...
Page 57
... A word write operation should be preceded by an erase of the corresponding memory location(s). The write typically requires complete, but the write time will vary with voltage and temperature. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 A program or erase operation on the data EEPROM does not stop the instruction flow. The user is respon- ...
Page 58
... Block all interrupts with priority <7 ; for next 5 instructions ; ; Write the 0x55 key ; ; Write the 0xAA key ; Initiate erase sequence ; Block all interrupts with priority <7 ; for next 5 instructions ; ; Write the 0x55 key ; ; Write the 0xAA key ; Initiate erase sequence © 2008 Microchip Technology Inc. ...
Page 59
... NOP ; Write cycle will complete in 2mS. CPU is not stalled for the Data Write Cycle ; User can poll WR bit, use NVMIF or Timer IRQ to determine write complete © 2008 Microchip Technology Inc. dsPIC30F5015/5016 The write will not initiate if the above sequence is not exactly followed (write 0x55 to NVMKEY, write 0xAA to NVMCON, then set WR bit) for each word ...
Page 60
... EEPROM writes, various mechanisms have been built-in. On power-up, the WREN bit is cleared; also, the Power-up Timer prevents EEPROM write. The write initiate sequence and the WREN bit together help prevent an accidental write during brown-out, power glitch or software malfunction. © 2008 Microchip Technology Inc. ...
Page 61
... WR TRIS WR LAT+ WR Port Read LAT Read Port © 2008 Microchip Technology Inc. dsPIC30F5015/5016 Writes to the latch, write the latch (LATx). Reads from the port (PORTx), read the port pins and writes to the port pins, write the latch (LATx). Any bit and its associated data and control registers that are not valid for a particular device will be disabled ...
Page 62
... Typically this instruction have their would be a NOP EXAMPLE 8-1: MOV 0xFF00, W0 MOV W0, TRISBB NOP BTSS PORTB, #13 I/O Cell I/O Pad Input Data PORT WRITE/READ EXAMPLE ; Configure PORTB<15:8> inputs ; and PORTB<7:0> as outputs ; Delay 1 cycle ; Next Instruction © 2008 Microchip Technology Inc. ...
Page 63
TABLE 8-1: dsPIC30F5015 PORT REGISTER MAP SFR Addr. Bit 15 Bit 14 Bit 13 Bit 12 Name TRISA 02C0 — — — — PORTA 02C2 — — — — LATA 02C4 — — — — TRISB 02C6 TRISB15 TRISB14 TRISB13 ...
Page 64
... TABLE 8-2: dsPIC30F5016 PORT REGISTER MAP SFR Addr. Bit 15 Bit 14 Bit 13 Bit 12 Name TRISA 02C0 TRISA15 TRISA14 — — PORTA 02C2 RA15 RA14 — — LATA 02C4 LATA15 LATA14 — — TRISB 02C6 TRISB15 TRISB14 TRISB13 TRISB12 TRISB11 TRISB10 TRISB9 TRISB8 TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 ...
Page 65
... Legend: — = unimplemented bit, read as ‘0’ Note 1: Refer to “dsPIC30F Family Reference Manual” (DS70046) for descriptions of register bit fields. TABLE 8-6: INPUT CHANGE NOTIFICATION REGISTER MAP (BITS 7-0) FOR dsPIC30F5016 SFR Addr. Bit 7 Bit 6 Name CNEN1 00C0 CN7IE ...
Page 66
... NOTES: DS70149D-page 66 © 2008 Microchip Technology Inc. ...
Page 67
... Timer operation during CPU Idle and Sleep modes • Interrupt on 16-bit Period register match or falling edge of external gate signal © 2008 Microchip Technology Inc. dsPIC30F5015/5016 These operating modes are determined by setting the appropriate bit(s) in the 16-bit SFR, T1CON. Figure 9-1 presents a block diagram of the 16-bit timer module ...
Page 68
... Period register and be reset to 0x0000. When a match between the timer and the Period register occurs, an interrupt can be generated, if the respective timer interrupt enable bit is asserted. TSYNC Sync 1 0 TCKPS<1:0> TON 2 Prescaler 1, 8, 64, 256 © 2008 Microchip Technology Inc. ...
Page 69
... XTAL SOSCO pF 100K © 2008 Microchip Technology Inc. dsPIC30F5015/5016 9.5.1 RTC OSCILLATOR OPERATION When the TON = 1, TCS = 1 and TGATE = 0, the timer increments on the rising edge of the 32 kHz LP oscillator output signal the value specified in the Period register, and is then reset to ‘0’. ...
Page 70
TABLE 9-1: TIMER1 REGISTER MAP SFR Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 TMR1 0100 PR1 0102 T1CON 0104 TON — TSIDL — Legend uninitialized bit; — = unimplemented bit, read as ‘0’ Note ...
Page 71
... Interrupt on a 32-bit Period register Match These operating modes are determined by setting the appropriate bit(s) in the 16-bit T2CON and T3CON SFRs. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 For 32-bit timer/counter operation, Timer2 is the least significant word and Timer3 is the most significant word of the 32-bit timer ...
Page 72
... Timer Configuration bit T32, (T2CON<3>), must be set to ‘1’ for a 32-bit timer/counter operation. All control bits are respective to the T2CON register. DS70149D-page 72 16 TMR2 Sync LSB PR2 Q D TGATE (T2CON<6> TON 1 x Gate 0 1 Sync TCKPS<1:0> 2 Prescaler 1, 8, 64, 256 © 2008 Microchip Technology Inc. ...
Page 73
... T3IF Event Flag 1 TGATE Note: The dsPIC30F5015/5016 devices do not have external pin inputs to Timer3. In these devices, the following modes should not be used: 1. TCS = 1 2. TCS = 0 and TGATE = 1 (gated time accumulation) © 2008 Microchip Technology Inc. dsPIC30F5015/5016 PR2 TMR2 Q D TGATE Q CK ...
Page 74
... In this mode, the T3IF interrupt flag is used as the source of the interrupt. The T3IF bit must be cleared in software. Enabling an interrupt is accomplished via the respective Timer Interrupt Enable bit, T3IE (IEC0<7>). © 2008 Microchip Technology Inc. ...
Page 75
TABLE 10-1: TIMER2/3 REGISTER MAP SFR Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 TMR2 0106 TMR3HLD 0108 TMR3 010A PR2 010C PR3 010E T2CON 0110 TON — TSIDL — T3CON 0112 TON — TSIDL — ...
Page 76
... NOTES: DS70149D-page 76 © 2008 Microchip Technology Inc. ...
Page 77
... TGATE (T4CON<6>) T4CK Note: Timer Configuration bit T45, (T4CON<3>), must be set to ‘ control bits are respective to the T4CON register. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 The Timer4/5 module is similar in operation to the Timer2/3 module. differences, which are listed below: • The Timer4/5 module does not support the ADC Event Trigger feature • ...
Page 78
... TCS = 1 2. TCS = 0 and TGATE = 1 (gated time accumulation) DS70149D-page 78 PR4 TMR4 Q D TGATE CK Q TON 1 x Gate Sync PR5 Comparator x 16 TMR5 Q D TGATE CK Q Sync Sync TCKPS<1:0> 2 Prescaler 1, 8, 64, 256 TCKPS<1:0> TON 2 Prescaler 1, 8, 64, 256 © 2008 Microchip Technology Inc. ...
Page 79
TABLE 11-1: TIMER4/5 REGISTER MAP SFR Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 TMR4 0114 TMR5HLD 0116 TMR5 0118 PR4 011A PR5 011C T4CON 011E TON — TSIDL — T5CON 0120 TON — TSIDL — Legend: u ...
Page 80
... NOTES: DS70149D-page 80 © 2008 Microchip Technology Inc. ...
Page 81
... ICBNE, ICOV ICxCON Data Bus Note: Where ‘x’ is shown, reference is made to the registers or bits associated to the respective input capture channels 1 through N. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 These operating modes are determined by setting the appropriate bits (where x = 1,2,...,N). The dsPIC30F5015/5016 device has 8 capture channels ...
Page 82
... IFSx Status register. Enabling an interrupt is accomplished via the respective Capture Channel Interrupt Enable (ICxIE) bit. The Capture Interrupt Enable bit is located in the corresponding IEC Control register. © 2008 Microchip Technology Inc. occurs, if defined as ...
Page 83
TABLE 12-1: INPUT CAPTURE REGISTER MAP SFR Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 IC1BUF 0140 IC1CON 0142 — — ICSIDL — IC2BUF 0144 IC2CON 0146 — — ICSIDL — IC3BUF 0148 IC3CON 014A — — ICSIDL ...
Page 84
... NOTES: DS70149D-page 84 © 2008 Microchip Technology Inc. ...
Page 85
... TMR2<15:0 TMR3<15:0> Note: Where ‘x’ is shown, reference is made to the registers associated with the respective output compare channels 1 through N. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 Figure 13-1 depicts a block diagram of the output compare module. The key operational features of the output compare module include: • ...
Page 86
... This state will be maintained until both of the following events have occurred: • The external Fault condition has been removed. • The PWM mode has been re-enabled by writing to the appropriate control bits input state. The OCFLT bit © 2008 Microchip Technology Inc. ...
Page 87
... Timer3) is enabled and the TSIDL bit of the selected timer is set to logic ‘0’. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 When the selected TMRx is equal to its respective Period register, PRx, the following four events occur on the next increment cycle: • ...
Page 88
TABLE 13-1: OUTPUT COMPARE REGISTER MAP SFR Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 OC1RS 0180 OC1R 0182 OC1CON 0184 — — OCSIDL — OC2RS 0186 OC2R 0188 OC2CON 018A — — OCSIDL — OC3RS ...
Page 89
... PCDOUT Existing Pin Logic 0 UPDN Up/Down 1 © 2008 Microchip Technology Inc. dsPIC30F5015/5016 The operational features of the QEI include: • Three input channels for two phase signals and index pulse • 16-bit up/down position counter • Count direction status • Position Measurement (x2 and x4) mode • ...
Page 90
... Position counter reset by detection of index pulse, QEIM<2:0> = 110. • Position counter reset by match with MAXCNT, QEIM<2:0> = 111. The x4 Measurement mode provides for finer resolution data (more position counts) for determining motor position. © 2008 Microchip Technology Inc. upon the ...
Page 91
... The UPDN control/Status bit (QEICON<11>) can be used to select the count direction state of the Timer register. When UPDN = 1, the timer will count up. When UPDN = 0, the timer will count down. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 In addition, control bit, UDSRC (QEICON<0>), determines whether the timer count direction state is based on the logic state written into the UPDN control/Status bit (QEICON< ...
Page 92
... The QEI Interrupt Flag bit, QEIIF, is asserted upon occurrence of any of the above events. The QEIIF bit must be cleared in software. QEIIF is located in the IFS2 Status register. Enabling an interrupt is accomplished via the respective enable bit, QEIIE. The QEIIE bit is located in the IEC2 Control register. © 2008 Microchip Technology Inc. ...
Page 93
TABLE 14-1: QEI REGISTER MAP SFR Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Name QEICON 0122 CNTERR — QEISIDL INDX UPDN DFLTCON 0124 — — — — — POSCNT 0126 MAXCNT 0128 Legend: ...
Page 94
... NOTES: DS70149D-page 94 © 2008 Microchip Technology Inc. ...
Page 95
... Three Phase AC Induction Motor • Switched Reluctance (SR) Motor • Brushless DC (BLDC) Motor • Uninterruptible Power Supply (UPS) © 2008 Microchip Technology Inc. dsPIC30F5015/5016 The PWM module has the following features: • 8 PWM I/O pins with 4 duty cycle generators • 16-bit resolution • ...
Page 96
... PWM Generator Channel 2 Dead-Time #2 Generator and Override Logic PWM Generator Channel 1 Dead-Time #1 Generator and Override Logic Special Event Postscaler PTDIR PWM4H PWM4L PWM3H Output PWM3L Driver Block PWM2H PWM2L PWM1H PWM1L FLTA FLTB Special Event Trigger © 2008 Microchip Technology Inc. ...
Page 97
... Electronically Commutative Motors (ECMs). The interrupt signals generated by the PWM time base depend on the mode selection bits (PTMOD<1:0>) and the postscaler bits (PTOPS<3:0>) in the PTCON SFR. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 15.1.1 FREE-RUNNING MODE In Free-Running mode, the PWM time base counts upwards until the value in the Time Base Period register (PTPER) is matched ...
Page 98
... PTPER PTMR Value 0 Duty Cycle using PWM PERIOD • T (PTPER + (PTMR Prescale Value) PWM PERIOD (UP/DOWN MODE) 2 • T • (PTPER + (PTMR Prescale Value) PWM RESOLUTION • log ( PWM CY log (2) EDGE-ALIGNED PWM New Duty Cycle Latched Period © 2008 Microchip Technology Inc. ...
Page 99
... The Duty Cycle registers are 16 bits wide. The LSb of a Duty Cycle register determines whether the PWM edge occurs in the beginning. Thus, the PWM resolution is effectively doubled. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 15.5.1 DUTY CYCLE REGISTER BUFFERS The four PWM Duty Cycle registers are double-buffered to allow glitchless updates of the PWM outputs ...
Page 100
... On a load of the down timer due to a duty cycle comparison edge event. • write to the DTCON1 or DTCON2 registers. • On any device Reset. Note: The user should not modify the DTCON1 or DTCON2 values while the PWM module is operating (PTEN Unexpected results may occur. © 2008 Microchip Technology Inc 1). ...
Page 101
... When a match with the PTPER register occurs, the PTMR register is cleared, all active PWM I/O pins are driven to the inactive state, the PTEN bit is cleared and an interrupt is generated. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 Time selected by DTSxI bit ( 15.10 PWM Output Override ...
Page 102
... PWM cycle or half-cycle boundary. The operating mode for each Fault input pin is selected using the FLTAM and FLTBM control bits in the FLTACON and FLTBCON Special Function Registers. Each of the Fault pins can be controlled manually in can operate software. © 2008 Microchip Technology Inc. ...
Page 103
... PWM time base. The SEVTDIR control bit has no effect unless the PWM time base is configured for an Up/Down Counting mode. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 15.14.1 SPECIAL EVENT TRIGGER POSTSCALER The PWM special event trigger has a postscaler that allows a 1:1 to 1:16 postscale ratio ...
Page 104
TABLE 15-2: 8-OUTPUT PWM REGISTER MAP SFR Name Addr Bit 15 Bit 14 Bit 13 Bit 12 PTCON 01C0 PTEN — PTSIDL — PTMR 01C2 PTDIR PTPER 01C4 — SEVTCMP 01C6 SEVTDIR PWMCON1 01C8 — — — — PTMOD4 PTMOD3 ...
Page 105
... The user must perform reads of SPIxBUF if the module is used in a transmit only configuration to avoid a receive overflow condition (SPIROV = 1). © 2008 Microchip Technology Inc. dsPIC30F5015/5016 Transmit writes are also double-buffered. The user writes to SPIxBUF. When the master or slave transfer is completed, the contents of the Shift register (SPIxSR) is moved to the receive buffer ...
Page 106
... Shift clock Clock Edge Control Select Enable Master Clock SDOx SDIy SDIx SDOy LSb Serial Clock SCKx SCKy Secondary Primary Prescaler F Prescaler CY 1:1-1 16, 64 SPI Slave Serial Input Buffer (SPIyBUF) Shift Register (SPIySR) MSb LSb PROCESSOR 2 © 2008 Microchip Technology Inc. ...
Page 107
... Therefore, when the SSx pin is asserted low again, transmission/reception will begin at the MSb, even if SSx had been deasserted in the middle of a transmit/receive. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 16.4 SPI Operation During CPU Sleep Mode During Sleep mode, the SPI module is shutdown ...
Page 108
TABLE 16-1: SPI1 REGISTER MAP SFR Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Name SPI1STAT 0220 SPIEN — SPISIDL — SPI1CON 0222 — FRMEN SPIFSD — DISSDO MODE16 SPI1BUF 0224 Legend: — = unimplemented bit, ...
Page 109
... Thus, the I C module can operate either as a slave master bus. FIGURE 17-1: PROGRAMMER’S MODEL bit 15 bit 15 © 2008 Microchip Technology Inc. dsPIC30F5015/5016 17.1.1 VARIOUS I The following types • Slave operation with 7-bit address 2 • Slave operation with 10-bit address 2 • ...
Page 110
... DS70149D-page 110 I2CRCV I2CRSR LSB Addr_Match I2CADD Start and Collision Detect Generation Clock Stretching I2CTRN LSB Reload Control I2CBRG BRG Down Counter F CY Internal Data Bus Read Write Read Write Read Write Read Write Read Write Read © 2008 Microchip Technology Inc. ...
Page 111
... SDA is valid during SCL high (see timing diagram). The interrupt pulse is sent on the falling edge of the ninth clock pulse, regardless of the status of the ACK received from the master. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 17.3.2 SLAVE RECEPTION If the R_W bit received is a ‘0’ during an address match, then Receive mode is initiated ...
Page 112
... C bus have deasserted SCL. This ensures that a write to the SCLREL bit will not violate the minimum high time requirement for SCL. If the STREN bit is ‘0’, a software write to the SCLREL bit will be disregarded and have no effect on the SCLREL bit. © 2008 Microchip Technology Inc. ...
Page 113
... Generate a Stop condition on SDA and SCL. 2 • Configure the I C port to receive data. • Generate an ACK condition at the end of a received byte of data. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 2 17. Master Operation The master device generates all of the serial clock ...
Page 114
... I C OPERATION DURING CPU IDLE MODE 2 For the I C, the I2CSIDL bit selects if the module will stop on Idle or continue on Idle. If I2CSIDL = 0, the module will continue operation on assertion of the Idle mode. If I2CSIDL = 1, the module will stop on Idle © 2008 Microchip Technology Inc. ...
Page 115
TABLE 17-2: I C™ REGISTER MAP SFR Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 — — — — I2CRCV 0200 — — — — I2CTRN 0202 — — — — I2CBRG 0204 — I2CCON 0206 ...
Page 116
... NOTES: DS70149D-page 116 © 2008 Microchip Technology Inc. ...
Page 117
... UART TRANSMITTER BLOCK DIAGRAM Internal Data Bus UTXBRK Data UxTX Parity Note © 2008 Microchip Technology Inc. dsPIC30F5015/5016 18.1 UART Module Overview The key features of the UART module are: • Full-duplex 9-bit data communication • Even, Odd or No Parity options (for 8-bit data) • ...
Page 118
... Receive Buffer Control – Generate Flags – Generate Interrupt – Shift Data Characters 8-9 Load RSR to Buffer Receive Shift Register (UxRSR) 16 Divider 16x Baud Clock from Baud Rate Generator Read Read Write UxMODE UxSTA Control Signals UxRXIF © 2008 Microchip Technology Inc. ...
Page 119
... The STSEL bit determines whether one or two Stop bits will be used during data transmission. The default (Power-on) setting of the UART is 8 bits, no parity, 1 Stop bit (typically represented 1). © 2008 Microchip Technology Inc. dsPIC30F5015/5016 18.3 Transmitting Data 18.3.1 ...
Page 120
... UxRSR needs to transfer the character to the buffer. Once OERR is set, no further data is shifted in UxRSR (until the OERR bit is cleared in software or a Reset occurs). The data held in UxRSR and UxRXREG remains valid. © 2008 Microchip Technology Inc. RXB) ...
Page 121
... FERR bit set. The break character is loaded into the buffer. No further reception can occur until a Stop bit is received. Note that RIDLE goes high when the Stop bit has not been received yet. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 18.6 Address Detect Mode Setting the ADDEN bit (UxSTA< ...
Page 122
... For the UART, the USIDL bit selects if the module will stop operation when the device enters Idle mode, or whether the module will continue on Idle. If USIDL = 0, the module will continue operation during Idle mode. If USIDL = 1, the module will stop on Idle. © 2008 Microchip Technology Inc. ...
Page 123
TABLE 18-1: UART1 REGISTER MAP SFR Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 U1MODE 020C UARTEN — USIDL — U1STA 020E UTXISEL — — — UTXBRK UTXEN U1TXREG 0210 — — — — U1RXREG ...
Page 124
... NOTES: DS70149D-page 124 © 2008 Microchip Technology Inc. ...
Page 125
... Programmable Loopback mode supports self-test operation • Signaling via interrupt capabilities for all CAN receiver and transmitter error states © 2008 Microchip Technology Inc. dsPIC30F5015/5016 • Programmable clock source • Programmable link to timer module for time-stamping and network synchronization • ...
Page 126
... RXF2 A Acceptance Filter c RXF3 c Acceptance Filter e RXF4 p t Acceptance Filter RXF5 R M Identifier Data Field Receive RERRCNT Error Counter TERRCNT Transmit ErrPas Error BusOff Counter Protocol Finite State Machine Bit Timing Bit Timing Logic Generator (1) CiRX © 2008 Microchip Technology Inc. ...
Page 127
... Mod- ule Disable mode. The I/O pins will revert to normal I/O function when the module is in the Module Disable mode. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 The module can be programmed to apply a low-pass filter function to the CiRX input line while the module or the CPU is in Sleep mode. The WAKFIL bit (CiCFG2< ...
Page 128
... End-of-Frame (EOF) field. Reading the RXnIF flag will indicate which receive buffer caused the interrupt. • Wake-up interrupt The CAN module has woken up from Disable mode or the device has woken up from Sleep mode. © 2008 Microchip Technology Inc. ...
Page 129
... TXERR (CiTXnCON<4>) flag automatically cleared. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 Setting the TXREQ bit simply flags a message buffer as enqueued for transmission. When the module detects an available bus, it begins transmitting the message which has been determined to have the highest priority. ...
Page 130
... definition, the Nominal Bit Time has a minimum and a maximum the minimum nominal bit time is 1 μsec, corresponding to a maximum bit rate of 1 MHz. Phase Phase Segment 1 Segment 2 Sample Point . Also, by definition, Q Sync © 2008 Microchip Technology Inc. ...
Page 131
... SEG2PH<2:0> (CiCFG2<10:8>). The following requirement must be fulfilled while setting the lengths of the Phase Segments: • Propagation Segment + Phase1 Seg > = Phase2 Seg © 2008 Microchip Technology Inc. dsPIC30F5015/5016 19.6.5 SAMPLE POINT The sample point is the point of time at which the bus level is read and interpreted as the value of that respec- tive bit ...
Page 132
TABLE 19-1: CAN1 REGISTER MAP SFR Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 — — — C1RXF0SID 0300 C1RXF0EIDH 0302 — — — — C1RXF0EIDL 0304 Receive Acceptance Filter 0 Extended Identifier<5:0> — — — C1RXF1SID ...
Page 133
TABLE 19-1: CAN1 REGISTER MAP (CONTINUED) SFR Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 C1TX1B2 0358 Transmit Buffer 1 Byte 3 C1TX1B3 035A Transmit Buffer 1 Byte 5 C1TX1B4 035C Transmit Buffer 1 Byte 7 C1TX1CON ...
Page 134
... NOTES: DS70149D-page 134 © 2008 Microchip Technology Inc. ...
Page 135
... In the Idle mode, the clock sources are still active, but the CPU is shut-off. The RC oscillator option saves system cost, while the LP crystal option saves power. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 20.1 Oscillator System Overview The dsPIC30F oscillator system has the following modules and features: • ...
Page 136
... LP oscillator can be conveniently shared as system clock, as well as Real-Time Clock for Timer1. 3: Any higher will violate PLL input range. 4: Any lower will violate PLL input range. 5: Requires external R and C. Frequency operation MHz. DS70149D-page 136 Description (1) (2) (3) (3) (1) (4) (4) (1)(4) (1) (5) /4 output OSC (5) © 2008 Microchip Technology Inc. ...
Page 137
... FIGURE 20-1: OSCILLATOR SYSTEM BLOCK DIAGRAM OSC1 Primary Oscillator OSC2 TUN<4:0> 5 Internal Fast RC Oscillator (FRC) POR Done SOSCO 32 kHz LP Oscillator SOSCI © 2008 Microchip Technology Inc. dsPIC30F5015/5016 F PLL PLL x4, x8, x16 PLL Lock Primary Osc Primary Oscillator Stability Detector Oscillator Start-up Clock ...
Page 138
... OSC2 Function OSC2 0 1 OSC2 1 0 OSC2 1 1 OSC2 0 1 OSC2 1 0 OSC2 1 1 OSC2 0 1 OSC2 1 0 OSC2 OSC2 0 0 OSC2 1 0 CLKO 1 1 CLKO OSC2 0 0 (Note (Note (Note © 2008 Microchip Technology Inc. ...
Page 139
... PLL enters a phase locked state. Should the loop fall out of lock (e.g., due to noise), the lock signal will be rescinded. The state of this signal is reflected in the read-only LOCK bit in the OSCCON register. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 20.2.5 FAST RC OSCILLATOR (FRC) The FRC oscillator is a fast (7.37 MHz ± ...
Page 140
... Note: The application should not attempt to switch to a clock of frequency lower than 100 KHz when the Fail-Safe Clock Monitor is enabled. If clock switching is performed, the device may generate an oscillator fail trap and switch to the Fast RC oscillator. © 2008 Microchip Technology Inc. ...
Page 141
... POR V Rise DD Detect V DD Brown-out Reset BOREN Trap Conflict Illegal Opcode/ Uninitialized W Register © 2008 Microchip Technology Inc. dsPIC30F5015/5016 20.3 Reset The PIC18F1220/1320 differentiates between various kinds of Reset: a) Power-on Reset (POR) b) MCLR Reset during normal operation c) MCLR Reset during Sleep d) Watchdog Timer (WDT) Reset (during normal ...
Page 142
... Q1 clock, and the PC will jump to the Reset vector. The timing for the SYSRST signal is shown in Figure 20-3 through Figure 20-5. T OST T PWRT T OST T PWRT , which is POR ) is applied. The T PWRT PWRT + T . When these delays POR PWRT ) DD ): CASE 1 DD © 2008 Microchip Technology Inc. ...
Page 143
... If the FSCM is disabled and the system clock has not started, the device will frozen state at the Reset vector until the system clock starts. From the user’s perspective, the device will appear Reset until a system clock is available. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 T OST T PWRT 20 ...
Page 144
... Discharge (ESD) or Electrical Overstress (EOS). Note: Dedicated supervisory devices, such as the MCP1XX and MCP8XX, may also be used as an external Power-on Reset circuit. EXTERNAL POWER-ON RESET CIRCUIT (FOR SLOW V POWER-UP MCLR dsPIC30F C power-up slope DD powers DD pin breakdown due to Elec- PP © 2008 Microchip Technology Inc. ...
Page 145
... Trap Reset 0x000000 Illegal Operation Reset 0x000000 Legend unchanged Note 1: When the wake-up is due to an enabled interrupt, the PC is loaded with the corresponding interrupt vector. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 TRAPR IOPUWR EXTR SWR WDTO IDLE SLEEP POR BOR ...
Page 146
... Sleep mode upon WDT time-out. The Sleep and WDTO Status bits are both set and T delays are applied. LOCK PWRT (~10 μs) is applied. This is the smallest . PWRT delay and OST POR , POR and T ), the crystal oscillator PWRT © 2008 Microchip Technology Inc. ...
Page 147
... Idle mode upon WDT time-out. The Idle and WDTO Status bits are both set. Unlike wake-up from Sleep, there are no time delays involved in wake-up from Idle. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 20.6 Device Configuration Registers The Configuration bits in each device Configuration ...
Page 148
... PGD and PGC pin functions in all dsPIC30F devices EMUD1/EMUC1, EMUD2/EMUC2 EMUD3/EMUC3 is selected as the debug I/O pin pair, then a 7-pin interface is required, as the EMUDx/EMUCx pin functions ( are not multiplexed with the PGD and PGC pin functions. © 2008 Microchip Technology Inc. EMUD/EMUC, and , ...
Page 149
TABLE 20-7: SYSTEM INTEGRATION REGISTER MAP FOR dsPIC30F5015/5016 SFR Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Name RCON 0740 TRAPR IOPUWR BGST — — OSCCON 0742 — COSC<2:0> — 0744 — — — — — OSCTUN ...
Page 150
... NOTES: DS70149D-page 150 © 2008 Microchip Technology Inc. ...
Page 151
... The ADC has a unique REF REF feature of being able to operate while the device is in Sleep mode. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 The ADC module has six 16-bit registers: • A/D Control Register1 (ADCON1) • A/D Control Register2 (ADCON2) • A/D Control Register3 (ADCON3) • ...
Page 152
... AN1 in the dsPIC30F5015 variant. REF DS70149D-page 152 + CH1 ADC S/H - 10-bit Result + CH2 S/H - 16-word, 10-bit Dual Port + CH3 S/H CH1,CH2, - CH3,CH0 Sample/Sequence Sample Input Switches + CH0 S/H - © 2008 Microchip Technology Inc. Conversion Logic Buffer Control Input MUX Control ...
Page 153
... The channels are then converted sequentially. Obviously, if there is only 1 channel selected, the SIMSAM bit is not applicable. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 The CHPS bits selects how many channels are sampled. This can vary from channels. If CHPS selects 1 channel, the CH0 channel will be sampled at the sample clock and converted ...
Page 154
... ADC and the required operating conditions. . The source of the A/D CONVERSION CLOCK * (0.5*(ADCS<5:0> +1 time AD = 5V). Refer to Section 24.0 DD under AD A/D CONVERSION CLOCK CALCULATION nsec nsec (30 MIPS nsec = 2 • nsec = 4. (ADCS<5:0> nsec = ( nsec Msps sampling rate. Table 21-1 © 2008 Microchip Technology Inc. ...
Page 155
... Up to 256. 300 ksps Note 1: External V - and V + pins must be used for correct operation. See Figure 21-2 for recommended REF REF circuit. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 R Max V Temperature S DD 500Ω 4.5V to 5.5V -40°C to +85°C 500Ω ...
Page 156
... Sequential sampling must be used in this configuration to allow adequate sampling time on each input 0 0 Multiple Analog Inputs © 2008 Microchip Technology Inc. ...
Page 157
... X 750,000 by writing to the ADCS<5:0> control bits in the ADCON3 register • Configure the sampling time writing: SAMC<4:0> = 00010 © 2008 Microchip Technology Inc. dsPIC30F5015/5016 21.7.3 600 ksps CONFIGURATION GUIDELINE The configuration for 600 ksps operation is dependent on whether a single input pin sampled or whether multiple pins will be sampled ...
Page 158
... Refer to Table 24-40 for T and sample time requirements The combined V DD ≤ 250Ω Sampling Switch leakage V = 0.6V T ± 500 nA period of sampling AD ≤ 3 kΩ HOLD = DAC capacitance = 4 negligible if Rs ≤ 5 kΩ. PIN © 2008 Microchip Technology Inc. ...
Page 159
... Signed Integer d09 d09 d09 d09 d09 d09 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00 Integer 0 © 2008 Microchip Technology Inc. dsPIC30F5015/5016 If the A/D interrupt is enabled, the device will wake-up from Sleep. If the A/D interrupt is not enabled, the A/D module will then be turned off, although the ADON bit will remain set ...
Page 160
... Any external components connected (via high-impedance analog input pin (capacitor, zener diode, etc.) should have very little leakage current at the pin. and V as ESD the input voltage exceeds this SS © 2008 Microchip Technology Inc. ...
Page 161
TABLE 21-2: ADC REGISTER MAP SFR Name Addr. Bit 15 Bit 14 Bit 13 Bit 12 ADCBUF0 0280 — — — — ADCBUF1 0282 — — — — ADCBUF2 0284 — — — — ADCBUF3 0286 — — — ...
Page 162
... NOTES: DS70149D-page 162 © 2008 Microchip Technology Inc. ...
Page 163
... The file register specified by the value ‘f’ • The destination, which could either be the file register ‘f’ or the W0 register, which is denoted as ‘WREG’ © 2008 Microchip Technology Inc. dsPIC30F5015/5016 Most bit oriented instructions (including simple rotate/shift instructions) have two operands: • ...
Page 164
... Moreover, double-word moves require two cycles. The double-word instructions execute in two instruction cycles. indirect Note: For more details on the instruction set, writes and refer to the “dsPIC30F/33F Programmer’s Reference Manual” (DS70157). Description © 2008 Microchip Technology Inc. ...
Page 165
... Y data space prefetch address register for DSP instructions Wy ∈ {[W10 [W10 [W10 [W10], [W10 [W10 [W10 [W11 [W11 [W11 [W11], [W11 [W11 [W11 [W11+W12], none} Y data space prefetch destination register for DSP instructions ∈ {W4..W7} Wyd © 2008 Microchip Technology Inc. dsPIC30F5015/5016 Description DS70149D-page 165 ...
Page 166
... Branch if accumulator B saturated Branch Unconditionally Branch if Zero Computed Branch Bit Set f Bit Set Ws Write C bit to Ws<Wb> Write Z bit to Ws<Wb> Bit Toggle f Bit Toggle Ws Bit Test f, Skip if Clear Bit Test Ws, Skip if Clear © 2008 Microchip Technology Inc Status Flags cycles Affected 1 1 OA,OB,SA, C,DC,N,OV,Z 1 ...
Page 167
... Wn,Expr Wm*Wm,Acc,Wx,Wy,Wxd 33 EDAC EDAC Wm*Wm,Acc,Wx,Wy,Wxd 34 EXCH EXCH Wns,Wnd © 2008 Microchip Technology Inc. dsPIC30F5015/5016 # of Description words Bit Test f, Skip if Set Bit Test Ws, Skip if Set Bit Test f Bit Test Bit Test Bit Test Ws<Wb> Bit Test Ws<Wb> Bit Test then Set f Bit Test then Set ...
Page 168
... Wm by Wn) to Accumulator Multiply and Subtract from Accumulator {Wnd+1, Wnd} = signed(Wb) * signed(Ws) {Wnd+1, Wnd} = signed(Wb) * unsigned(Ws) {Wnd+1, Wnd} = unsigned(Wb) * signed(Ws) {Wnd+1, Wnd} = unsigned(Wb) * unsigned(Ws) {Wnd+1, Wnd} = signed(Wb) * unsigned(lit5) {Wnd+1, Wnd} = unsigned(Wb) * unsigned(lit5) W3: WREG © 2008 Microchip Technology Inc Status Flags cycles Affected ...
Page 169
... SFTAC Acc,Wn SFTAC Acc,#Slit6 f,WREG SL Ws,Wd SL Wb,Wns,Wnd SL Wb,#lit5,Wnd © 2008 Microchip Technology Inc. dsPIC30F5015/5016 # of Description words Negate Accumulator WREG = Operation No Operation Pop f from Top-of-Stack (TOS) Pop from Top-of-Stack (TOS) to Wdo Pop from Top-of-Stack (TOS) to W(nd):W(nd+1) Pop Shadow Registers ...
Page 170
... Wn = byte swap Wn Read Prog<23:16> to Wd<7:0> Read Prog<15:0> Write Ws<7:0> to Prog<23:16> Write Ws to Prog<15:0> Unlink Frame Pointer .XOR. WREG WREG = f .XOR. WREG Wd = lit10 .XOR .XOR .XOR. lit5 Wnd = Zero-Extend Ws © 2008 Microchip Technology Inc Status Flags cycles Affected 1 1 OA,OB,OAB, SA,SB,SAB 1 1 C,DC,N,OV,Z ...
Page 171
... PICSTART Plus Development Programmer - MPLAB PM3 Device Programmer - PICkit™ 2 Development Programmer • Low-Cost Demonstration and Development Boards and Evaluation Kits © 2008 Microchip Technology Inc. dsPIC30F5015/5016 23.1 MPLAB Integrated Development Environment Software The MPLAB IDE software brings an ease of software development previously unseen in the 8/16-bit microcontroller market ...
Page 172
... MPLAB C30 C Compilers, and the MPASM and MPLAB ASM30 Assemblers. The software simulator offers the flexibility to develop and debug code outside of the hardware laboratory environment, making it an excellent, economical software development tool PC-hosted environment by ® DSCs on an © 2008 Microchip Technology Inc. ...
Page 173
... MPLAB REAL ICE offers significant advantages over competitive emulators including low-cost, full-speed emulation, real-time variable watches, trace analysis, complex breakpoints, a ruggedized probe interface and long (up to three meters) interconnection cables. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 23.9 MPLAB ICD 2 In-Circuit Debugger Microchip’s In-Circuit Debugger, MPLAB ICD ...
Page 174
... ICs, CAN, IrDA EE OQ ® battery management, SEEVAL evaluation system, Sigma-Delta ADC, flow rate sensing, plus many more. Check the Microchip web page (www.microchip.com) for the complete list of demonstration, development and evaluation kits. © 2008 Microchip Technology Inc. kits and ® , PowerSmart ...
Page 175
... This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 (1) ...
Page 176
... Temp Range DD (in Volts) (in °C) 4.5-5.5 -40 to +85 4.5-5.5 -40 to +125 3.0-3.6 -40 to +85 3.0-3.6 -40 to +125 2.5-3.0 -40 to +85 TABLE 24-2: OPERATING MIPS VS. VOLTAGE FOR dsPIC30F5016 V Range Temp Range DD (in Volts) (in °C) 4.5-5.5 -40 to +85 4.5-5.5 -40 to +125 3.0-3.6 -40 to +85 3.0-3.6 -40 to +125 2.5-3.0 ...
Page 177
... Data in “Typ” column is at 5V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: These parameters are characterized but not tested in manufacturing. 3: This is the limit to which V DD © 2008 Microchip Technology Inc. dsPIC30F5015/5016 Standard Operating Conditions: 2.5V to 5.5V (unless otherwise stated) Operating temperature (1) Min ...
Page 178
... OSC1 DD 0.128 MIPS LPRC (512 kHz) (1.8 MIPS) FRC (7.37 MHz) 4 MIPS 10 MIPS 20 MIPS 30 MIPS . DD © 2008 Microchip Technology Inc. ...
Page 179
... Data in “Typical” column is at 5V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: Base I current is measured with Core off, Clock on and all modules turned off. IDLE © 2008 Microchip Technology Inc. dsPIC30F5015/5016 ) IDLE Standard Operating Conditions: 2.5V to 5.5V (unless otherwise stated) -40° ...
Page 180
... PD Base Power Down Current (3) Watchdog Timer Current: ΔI WDT (3) Timer 1 w/32 kHz Crystal: Δ (3) BOR On: ΔI BOR © 2008 Microchip Technology Inc. ...
Page 181
... The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 5: Negative current is defined as current sourced by the pin. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 Standard Operating Conditions: 2.5V to 5.5V (unless otherwise stated) Operating temperature ...
Page 182
... Industrial A ≤ +125°C for Extended A Units Conditions 8.5 mA 2.0 mA 1.6 mA 2.0 mA -3.0 mA -2.0 mA -1.3 mA -2.0 mA XTL, XT, HS and LP modes when external clock is used to drive OSC1 Osc mode C™ mode (Device not in Brown-out Reset) © 2008 Microchip Technology Inc. ...
Page 183
... EB DD Note 1: Data in “Typ” column is at 5V, 25°C unless otherwise stated. 2: These parameters are characterized but not tested in manufacturing. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 Standard Operating Conditions: 2.5V to 5.5V (unless otherwise stated) -40°C ≤ T ≤ +85°C for Industrial Operating temperature A -40° ...
Page 184
... DC Spec Section 24.1 “DC DD Characteristics”. Load Condition 2 – for OSC2 Pin 464Ω for all pins except OSC2 for OSC2 output OS20 OS30 OS30 OS25 OS40 ≤ +85°C for Industrial A ≤ +125°C for Extended OS31 OS31 OS41 © 2008 Microchip Technology Inc. ...
Page 185
... Measurements are taken ERC modes. The CLKO signal is measured on the OSC2 pin. CLKO is low for the Q1-Q2 period (1/2 T © 2008 Microchip Technology Inc. dsPIC30F5015/5016 Standard Operating Conditions: 2.5V to 5.5V (unless otherwise stated) ...
Page 186
... V = 4 ≤ +85° 3 ≤ +125° 3 ≤ +85° 4 ≤ +125° 4 ≤ +85° 3 ≤ +85° 4 ≤ +125° 4 © 2008 Microchip Technology Inc. ...
Page 187
... CY (1) (MHz) Mode EC 0.200 Note 1: Assumption: Oscillator Postscaler is divide Instruction Execution Cycle Time Instruction Execution Frequency: MIPS = (F cycle). © 2008 Microchip Technology Inc. dsPIC30F5015/5016 (3) (3) MIPS MIPS (2) (μsec) w/o PLL w PLL x4 20.0 0.05 — 1.0 1.0 4.0 0.4 2.5 10.0 0.16 6.25 — ...
Page 188
... DD ≤ +85°C for Industrial ≤ +125°C for Extended Conditions ≤ +85° 3.0-5. ≤ +125° 3.0-5. ≤ +85°C for Industrial A ≤ +125°C for Extended A Conditions V = 5.0V, ±10 3.3V, ±10 2.5V DD © 2008 Microchip Technology Inc. ...
Page 189
... These parameters are asynchronous events not related to any internal clock edges. 2: Measurements are taken in RC mode and EC mode where CLKO output These parameters are characterized but not tested in manufacturing. 4: Data in “Typ” column is at 5V, 25°C unless otherwise stated. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 DI35 DI40 New Value DO31 DO32 Standard Operating Conditions: 2 ...
Page 190
... TIMER TIMING CHARACTERISTICS V DD SY12 MCLR Internal POR SY11 PWRT Time-out SY30 OSC Time-out Internal Reset Watchdog Timer Reset I/O Pins SY35 FSCM Delay Note: Refer to Figure 24-2 for load conditions. DS70149D-page 190 SY10 SY20 SY13 SY13 © 2008 Microchip Technology Inc. ...
Page 191
... TABLE 24-22: BAND GAP START-UP TIME REQUIREMENTS AC CHARACTERISTICS Param Symbol Characteristic No. SY40 T Band Gap Start-up Time BGAP Note 1: These parameters are characterized but not tested in manufacturing. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 Standard Operating Conditions: 2.5V to 5.5V (unless otherwise stated) Operating temperature (1) (2) Min Typ Max 2 — ...
Page 192
... Industrial A ≤ +125°C for Extended A Max Units Conditions — ns Must also meet parameter TA15 — ns — ns — ns Must also meet parameter TA15 — ns — ns — ns — — prescale value (1, 8, 64, 256) — kHz 1.5 T — CY © 2008 Microchip Technology Inc. ...
Page 193
... TxCK Low Time TC15 TtxP TxCK Input Period Synchronous, TC20 T Delay from External TxCK Clock CKEXTMRL Edge to Timer Increment © 2008 Microchip Technology Inc. dsPIC30F5015/5016 Standard Operating Conditions: 2.5V to 5.5V (unless otherwise stated) -40°C ≤ T Operating temperature -40°C ≤ T Min Typ Synchronous, 0 ...
Page 194
... CY with prescaler Synchronous with prescaler Synchronous with prescaler 0 TQ20 ≤ +85°C for Industrial A ≤ +125°C for Extended A Max Units Conditions — ns Must also meet parameter TQ15 — ns Must also meet parameter TQ15 — © 2008 Microchip Technology Inc. ...
Page 195
... Note 1: These parameters are characterized but not tested in manufacturing. 2: Data in “Typ” column is at 5V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 IC10 IC11 IC15 Standard Operating Conditions: 2.5V to 5.5V (unless otherwise stated) -40° ...
Page 196
... DS70149D-page 196 OC20 Standard Operating Conditions: 2.5V to 5.5V (unless otherwise stated) -40°C ≤ T Operating temperature -40°C ≤ T (1) (2) Min Typ Max — — — — ≤ +85°C for Industrial A ≤ +125°C for Extended A Units Conditions ns ns © 2008 Microchip Technology Inc. ...
Page 197
... These parameters are characterized but not tested in manufacturing. 2: Data in “Typ” column is at 5V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 MP30 MP11 MP10 Standard Operating Conditions: 2.5V to 5.5V (unless otherwise stated) -40° ...
Page 198
... T Operating temperature -40°C ≤ T (1) (2) Typ Max 6 T — — — — — — CY ≤ +85°C for Industrial A ≤ +125°C for Extended A Units Conditions 16, 32, 64, 128 and 256 (Note 16, 32, 64, 128 and 256 (Note 2) © 2008 Microchip Technology Inc. ...
Page 199
... Alignment of index pulses to QEA and QEB is shown for position counter reset timing only. Shown for forward direction only (QEA leads QEB). Same timing applies for reverse direction (QEA lags QEB) but index pulse recognition occurs on falling edge. © 2008 Microchip Technology Inc. dsPIC30F5015/5016 TQ50 TQ55 Standard Operating Conditions: 2 ...
Page 200
... Industrial A -40°C ≤ T ≤ +125°C for Extended A Max Units Conditions — ns — ns — ns See parameter DO32 — ns See parameter DO31 — ns See parameter DO32 — ns See parameter DO31 30 ns — ns — ns © 2008 Microchip Technology Inc. ...