PIC12F675-E/P Microchip Technology, PIC12F675-E/P Datasheet - Page 17

• Manufacturer Part Number: PIC12F675-E/P
• Description: IC MCU CMOS 1K FLASH W/AD 8-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 12Fr

Specifications of PIC12F675-E/P

• Program Memory Type: FLASH
• Program Memory Size: 1.75KB (1K x 14)
• Package / Case: 8-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: POR, WDT
• Number Of I /o: 5
• Eeprom Size: 128 x 8
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: PIC12F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 64 B
• Interface Type: RS- 232, USB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 8
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 53270-913
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-4
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM163029 - BOARD PICDEM FOR MECHATRONICSAC124001 - MODULE SKT PROMATEII 8DIP/SOIC
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

3.0
The
Configuration bits. These bits can be programmed
(reads ‘0’) or left unchanged (reads ‘1’) to select
various device configurations.
REGISTER 3-1:
© 2005 Microchip Technology Inc.
bit 13
bit 13-12 BG<1:0>: Band Gap Calibration bits
bit 11-9 Unimplemented: Read as ‘0’
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2-0
R/P-1 R/P-1
BG1
PIC12F629/675/PIC16F630/676
CONFIGURATION WORD
BG0
00 = Lowest band gap voltage
...
11 = Highest band gap voltage
CPD: Code Protection Data bit
1 = Data memory is not protected
0 = Data memory is external read protected
CP: Code Protection bit
1 = Program memory is not code-protected
0 = Program memory is code-protected
BODEN: Brown-out Detect Enable bit
1 = BOD enabled
0 = BOD disabled
MCLRE: MCLR Pin Function Select bit
1 = MCLR pin is MCLR function
0 = MCLR pin is alternate function, MCLR function is internally disabled
PWRTE: Power-up Timer Enable bit
1 = PWRT disabled
0 = PWRT enabled
WDTE: Watchdog Timer Enable bit
1 = WDT enabled
0 = WDT disabled
FOSC<2:0>: Oscillator Selection bits
000 = LP oscillator: Low-power crystal on GP5/T1CKI/OSC1/CLKIN and GP4/T1G/OSC2/CLKOUT
001 = XT oscillator: Crystal/resonator on GP5/T1CKI/OSC1/CLKIN and GP4/T1G/OSC2/CLKOUT
010 = HS oscillator: High-speed crystal/resonator on GP5/T1CKI/OSC1/CLKIN and GP4/T1G/OSC2/CLKOUT
011 = EC: I/O function on GP4/T1G/OSC2/CLKOUT, CLKIN on GP5/T1CKI/OSC1/CLKIN
100 = INTOSC oscillator: I/O function on GP4/T1G/OSC2/CLKOUT, I/O function on GP5/T1CKI/OSC1/CLKIN
101 = INTOSC oscillator: CLKOUT function on GP4/T1G/OSC2/CLKOUT, I/O function on GP5/T1CKI/OSC1/
110 = RC oscillator: I/O function on GP4/T1G/OSC2/CLKOUT, RC on GP5/T1CKI/OSC1/CLKIN
111 = RC oscillator: CLKOUT function on GP4/T1G/OSC2/CLKOUT, RC on GP5/T1CKI/OSC1/CLKIN
Legend:
R = Readable bit
-n = Value at POR
Note 1: Enabling Brown-out Detect Reset Enable does not automatically enable the Power-up Timer
CLKIN
U-0
2: The Band Gap Calibration bits must be read and preserved, then replaced by the user during any
3: GP4 and GP5 apply to PIC12F629/675 only. For PIC16F630/676, use RA4 and RA5,
—
Enable (PWRTE).
bulk erase operation.
respectively.
CONFIGURATION WORD FOR PIC12F629/675/PIC16F630/676
U-0
—
U-0
—
W = Writable bit
‘1’ = Bit is set
R/P-1 R/P-1
CPD
PIC12F629/675/PIC16F630/676
has
CP
(1)
(2)
several
(3)
(1)
BODEN MCLRE PWRTE WDTE FOSC2 FOSC1 FOSC0
R/P-1
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/P-1
R/P-1
R/P-1
x = Bit is unknown
R/P-1
DS41191D-page 17
R/P-1
R/P-1
bit 0