ST7FLITE05Y0B6 STMicroelectronics, ST7FLITE05Y0B6 Datasheet - Page 34

• Manufacturer Part Number: ST7FLITE05Y0B6
• Description: IC MCU 8BIT 1.5K FLASH 16-DIP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FLITE05Y0B6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 13
• Program Memory Size: 1.5KB (1.5K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 5.5 V
• Data Converters: A/D 5x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-DIP (0.300", 7.62mm)
• Processor Series: ST7FLITE0x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 2
• Operating Supply Voltage: 2.4 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: ST7FLIT0-IND/USB, ST7FLITE-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• For Use With: 497-5858 - EVAL BOARD PLAYBACK ST7FLITE497-5080 - EVAL BOARD AC/AC CHOPPER DRIVER497-5049 - KIT STARTER RAISONANCE ST7FLITE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: In Transition

ST7LITE0xY0, ST7LITESxY0
SYSTEM INTEGRITY MANAGEMENT (Cont’d)
8.4.2 Auxiliary Voltage Detector (AVD)
The Voltage Detector function (AVD) is based on
an analog comparison between a V
V
ply voltage (V
for falling voltage is lower than the V
ence value for rising voltage in order to avoid par-
asitic detection (hysteresis).
The output of the AVD comparator is directly read-
able by the application software through a real
time status bit (AVDF) in the SICSR register. This
bit is read only.
Caution: The AVD functions only if the LVD is en-
abled through the option byte.
Figure 21. Using the AVD to Monitor V
34/124
1
IT+(AVD)
AVDF bit
AVD INTERRUPT
REQUEST
IF AVDIE bit = 1
LVD RESET
V
V
V
V
IT+(AVD)
IT+(LVD)
IT-(LVD)
IT-(AVD)
reference value and the V
V
AVD
DD
). The V
0
IT-(AVD)
1
reference value
IT+(AVD)
DD
INTERRUPT Cleared by
IT-(AVD)
main sup-
V
Early Warning Interrupt
(Power has dropped, MCU not
not yet in reset)
DD
hyst
refer-
reset
and
RESET
8.4.2.1 Monitoring the V
The AVD voltage threshold value is relative to the
selected LVD threshold configured by option byte
(see
If the AVD interrupt is enabled, an interrupt is gen-
erated when the voltage crosses the V
V
In the case of a drop in voltage, the AVD interrupt
acts as an early warning, allowing software to shut
down safely before the LVD resets the microcon-
troller. See
The interrupt on the rising edge is used to inform
the application that the V
IT-(AVD)
section 15.1 on page
threshold (AVDF bit is set).
Figure
21.
1
DD
INTERRUPT Cleared by
DD
112).
warning state is over
Main Supply
hardware
0
IT+(LVD)
or