SAK-TC1797-512F180E AC Infineon Technologies, SAK-TC1797-512F180E AC Datasheet - Page 24

• Manufacturer Part Number: SAK-TC1797-512F180E AC
• Description: IC MCU 32BIT FLASH 416-BGA
• Manufacturer: Infineon Technologies
• Series: TC17xxr

Specifications of SAK-TC1797-512F180E AC

• Core Processor: TriCore
• Core Size: 32-Bit
• Speed: 180MHz
• Connectivity: ASC, CAN, EBI/EMI, MLI, MSC, SSC
• Peripherals: DMA, POR, WDT
• Number Of I /o: 219
• Program Memory Size: 4MB (4M x 8)
• Program Memory Type: FLASH
• Ram Size: 224K x 8
• Voltage - Supply (vcc/vdd): 1.42 V ~ 1.58 V
• Data Converters: A/D 48x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 416-BGA
• Packages: PG-BGA-416
• Max Clock Frequency: 180.0 MHz
• Sram (incl. Cache): 224.0 KByte
• Can Nodes: 4
• A / D Input Lines (incl. Fadc): 48
• Program Memory: 4.0 MB
• For Use With: B158-H8537-G2-X-7600IN - KIT STARTER TC179X FAMILY
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: SP000432392

2.3.3
The TC1797’s STM is designed for global system timing applications requiring both high
precision and long range.
Features
•
•
•
•
•
•
•
•
Special STM register semantics provide synchronous views of the entire 56-bit counter,
or 32-bit subsets at different levels of resolution.
The maximum clock period is 2
25.39 years before overflowing. Thus, it is capable of continuously timing the entire
expected product life time of a system without overflowing.
In case of a power-on reset, a watchdog reset, or a software reset, the STM is reset. After
one of these reset conditions, the STM is enabled and immediately starts counting up. It
is not possible to affect the content of the timer during normal operation of the TC1797.
The STM can be optionally disabled for power-saving purposes, or suspended for
debugging purposes via its clock control register. In suspend mode of the TC1797
(initiated by writing an appropriate value to STM_CLC register), the STM clock is
stopped but all registers are still readable.
Due to the 56-bit width of the STM, it is not possible to read its entire content with one
instruction. It needs to be read with two load instructions. Since the timer would continue
to count between the two load operations, there is a chance that the two values read are
not consistent (due to possible overflow from the low part of the timer to the high part
between the two read operations). To enable a synchronous and consistent reading of
the STM content, a capture register (STM_CAP) is implemented. It latches the content
of the high part of the STM each time when one of the registers STM_TIM0 to STM_TIM5
is read. Thus, STM_CAP holds the upper value of the timer at exactly the same time
when the lower part is read. The second read operation would then read the content of
the STM_CAP to get the complete timer value.
The content of the 56-bit System Timer can be compared against the content of two
compare values stored in the STM_CMP0 and STM_CMP1 registers. Interrupts can be
generated on a compare match of the STM with the STM_CMP0 or STM_CMP1
registers.
Data Sheet
Free-running 56-bit counter
All 56 bits can be read synchronously
Different 32-bit portions of the 56-bit counter can be read synchronously
Flexible interrupt generation based on compare match with partial STM content
Driven by maximum 90 MHz (=
Counting starts automatically after a reset operation
STM registers are reset by an application reset if bit ARSTDIS.STMDIS is cleared. If
bit ARSTDIS.STMDIS is set, the STM is not reset.
STM can be halted in debug/suspend mode
System Timer
56
×
f
f
STM
SYS
, default after reset =
. At
20
f
STM
= 90 MHz, for example, the STM counts
f
SYS
/2)
Introduction
V1.1, 2009-04
TC1797