LP2987AIMM-5.0/NOPB National Semiconductor, LP2987AIMM-5.0/NOPB Datasheet - Page 10
![IC REGULATOR MICROPWR LDO 8-MSOP](/photos/6/57/65756/pkg_mua08a_sml.jpg)
LP2987AIMM-5.0/NOPB
Manufacturer Part Number
LP2987AIMM-5.0/NOPB
Description
IC REGULATOR MICROPWR LDO 8-MSOP
Manufacturer
National Semiconductor
Datasheet
1.LP2987IM-3.3NOPB.pdf
(23 pages)
Specifications of LP2987AIMM-5.0/NOPB
Regulator Topology
Positive Fixed
Voltage - Output
5V
Voltage - Input
Up to 16V
Voltage - Dropout (typical)
0.18V @ 200mA
Number Of Regulators
1
Current - Output
200mA
Current - Limit (min)
250mA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*LP2987AIMM-5.0TR
LP2987AIMM-5.0
LP2987AIMM-5.0TR
LP2987AIMM-5.0
LP2987AIMM-5.0TR
www.national.com
I
SHUTDOWN INPUT
V
I
ERROR COMPARATOR
I
V
V
(MAX)
V
(MIN)
HYST
DELAY
S/D
OH
S/D
OL
THR
THR
Electrical Characteristics
Limits in standard typeface are for T
less otherwise specified: V
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating the
device outside of its rated operating conditions.
Note 2: The ESD rating of the Bypass pin is 500V (LP2988 only). The ESD rating of the V
Note 3: The maximum allowable power dissipation is a function of the maximum junction temperature, T
and the ambient temperature, T
The value of θ
dependent on PCB trace area, trace material, and the number of layers and thermal vias. For improved thermal resistance and power dissipation for the LLP
package, refer to Application Note AN-1187. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into
thermal shutdown.
Note 4: If used in a dual-supply system where the regulator load is returned to a negative supply, the LM2987/8 output must be diode-clamped to ground.
Note 5: The output PNP structure contains a diode between the V
on this diode and may induce a latch-up mode which can damage the part (see Application Hints).
Note 6: Limits are 100% production tested at 25˚C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate National’s Average Outgoing Quality Level (AOQL).
Note 7: Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below the value measured with a 1V differential.
Note 8: To prevent mis-operation, the Shutdown input must be driven by a signal that swings above V
Application Hints).
Note 9: Temperature coefficient is defined as the maximum (worst-case) change divided by the total temperature range.
Note 10: See Typical Performance Characteristics curves.
Symbol
J−A
Delay Pin Current
Source
S/D Input Voltage
(Note 8)
S/D Input Current
Output “HIGH” Leakage
Output “LOW” Voltage
Upper Threshold Voltage
Lower Threshold Voltage
Hysteresis
for the SO-8 (M) package is 160˚C/W, and the mini SO-8 (MM) package is 200˚C/W. The value θ
Parameter
A
. The maximum allowable power dissipation at any ambient temperature is calculated using:
IN
= V
O
(NOM) + 1V, I
J
= 25˚C, and limits in boldface type apply over the full operating temperature range. Un-
V
V
V
V
V
V
I
O
H
L
S/D
S/D
OH
IN
(COMP) = 300 µA
= O/P OFF
= O/P ON
= V
(Continued)
= 16V
= 0
= 5V
Conditions
O
L
(NOM) − 0.5V,
= 1 mA, C
IN
and V
OUT
OUT
terminals that is normally reverse-biased. Forcing the output above the input will turn
10
= 4.7 µF, C
Typical
0.55
0.01
−4.6
−6.6
150
2.2
1.4
2.0
0
5
IN
pin is 1kV and the Delay pin is ESD rated at 1.5kV.
IN
= 2.2 µF, V
LM2987/8AI-X.X
−13.0
H
−5.5
−7.7
−8.9
Min
1.6
1.4
1.6
and below V
J
(MAX), the junction-to-ambient thermal resistance, θ
(Note 6)
Max
0.18
−3.5
−2.5
−4.9
−3.3
S/D
220
350
2.8
3.0
L
−1
15
1
2
J−A
with a slew rate not less than 40 mV/µs (see
= 2V.
for the LLP (LD) package is specifically
−13.0
LM2987/8I-X.X
−5.5
−7.7
−8.9
Min
1.6
1.4
1.6
(Note 6)
Max
0.18
−3.5
−2.5
−4.9
−3.3
220
350
2.8
3.0
−1
15
1
2
%V
Units
mV
µA
µA
µA
V
OUT
J−A
,