CS5208-1GT3 ON Semiconductor, CS5208-1GT3 Datasheet - Page 2

• Manufacturer Part Number: CS5208-1GT3
• Description: IC REG LDO ADJ 8A TO220-3
• Manufacturer: ON Semiconductor

Specifications of CS5208-1GT3

• Regulator Topology: Positive Adjustable
• Voltage - Output: 1.25 ~ 4.5 V
• Voltage - Input: Up to 6V
• Voltage - Dropout (typical): 0.96V @ 8A
• Number Of Regulators: 1
• Current - Output: 8A
• Current - Limit (min): 8.1A
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Package / Case: TO-220-3 (Straight Leads)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: CS5208-1GT3OS

1. 10 second maximum.
*The maximum package power dissipation must be observed.
2. The minimum load current is the minimum current required to maintain regulation. Normally the current in the resistor divider used to set the
3. This parameter is guaranteed by design and is not 100% production tested.
4. Dropout voltage is defined as the minimum input/output voltage differential required to maintain 1.5% regulation.
5. This parameter is guaranteed by design, but not parametrically tested in production. However, a 100% thermal shutdown functional test is
MAXIMUM RATINGS*
ELECTRICAL CHARACTERISTICS
Adjustable Output Voltage
Input Voltage
Operating Junction Temperature Range
Storage Temperature Range
Lead Temperature Soldering:
ESD Damage Threshold
Reference Voltage
Line Regulation
Load Regulation
Minimum Load Current (Note 2)
Adjust Pin Current
Current Limit
Short Circuit Current
Ripple Rejection (Note 3)
Thermal Regulation (Note 3)
Dropout Voltage (Minimum V
RMS Output Noise
Temperature Stability
Thermal Shutdown (Note 5)
Thermal Shutdown Hysteresis (Note 5)
output voltage is selected to meet the minimum load current requirement.
performed on each part.
(Note 4)
Characteristic
IN
−V
OUT
)
( 0°C ≤ T
V
I
V
V
V
V
V
V
V
30 ms Pulse, T
I
I
I
I
I
Freq = 10 Hz to 10 kHz, T
OUT
OUT
OUT
OUT
OUT
OUT
IN
IN
IN
IN
IN
IN
IN
IN
I
OUT
= 3.25 V Avg, V
= 2.75 V to 5.5 V,
= 2.75 V to 5.5 V, I
= 2.75 V, I
= 5.0 V, ΔV
= 2.75 V, I
= 2.75 V, ΔV
= 2.75 V, V
= 10 mA to 8.0 A
= 100 mA
= 1.0 A
= 2.75 A
= 4.0 A
= 8.0 A
A
Parameter
= 4.0 A, C
≤ 70°C, 0°C ≤ T
http://onsemi.com
OUT
OUT
Test Conditions
OUT
A
OUT
OUT
= 25°C
Adj
= 10 mA to 8.0 A
= 10 mA
RIPPLE
= 0 V
= +1.5%
= 0.1 μF; C
= −1.5%
Wave Solder (through hole styles only) Note 1
OUT
−
−
−
J
2
≤ 150°C, V
A
= 1.0 V
= 10 mA
= 25°C
OUT
P−P
= 22 μF
Adj
@ 120 Hz,
= 0 V, unless otherwise specified.)
(−1.5%)
1.234
Min
150
8.1
6.0
60
−
−
−
−
−
−
−
−
−
−
−
−
−
1.253
0.002
0.003
0.02
0.04
0.92
0.93
0.94
0.95
0.96
Typ
180
5.0
9.0
8.5
0.5
70
80
25
0 ≤ T
−60 to +150
260 Peak
(+1.5%)
Value
1.271
6.0
2.0
Max
0.20
0.50
1.15
1.15
1.15
1.15
1.30
120
210
J
10
−
−
−
−
−
−
−
≤ 150
%V
%/W
Unit
mA
Unit
μA
dB
°C
°C
%
%
%
V
A
A
V
V
V
V
V
°C
°C
°C
kV
OUT
V