NBB-300-T1 RFMD, NBB-300-T1 Datasheet - Page 7

• Manufacturer Part Number: NBB-300-T1
• Description: IC AMP MMIC GAAS 12GHZ 4-MICROX
• Manufacturer: RFMD

Specifications of NBB-300-T1

• Current - Supply: 50mA
• Frequency: 0Hz ~ 12GHz
• Gain: 11dB ~ 13dB
• Noise Figure: 5.1dB @ 3GHz
• P1db: 13.8dBm @ 6GHz
• Package / Case: 4-Micro-X
• Rf Type: LMDS, VSAT, WLAN, UNII, DWDM, PTP PMP
• Voltage - Supply: 3.6V ~ 4.2V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Test Frequency: -
• Other names: 689-1000-2; NBB-300TR13

Carrier tape basic dimensions are based on EIA 481. The pocket is designed to hold the part for shipping and loading onto SMT
manufacturing equipment, while protecting the body and the solder terminals from damaging stresses. The individual pocket
design can vary from vendor to vendor, but width and pitch will be consistent.
Carrier tape is wound or placed onto a shipping reel 178 mm (7 inches) in diameter. The center hub design is large enough to
ensure the radius formed by the carrier tape around it does not put unnecessary stress on the parts.
Prior to shipping, moisture sensitive parts (MSL Level 2a-5a) are baked and placed into the pockets of the carrier tape. A cover
tape is sealed over the top of the entire length of the carrier tape. The reel is sealed in a moisture barrier ESD bag with the
appropriate units of desiccant and a humidity indicator card, which is placed in a cardboard shipping box. It is important to
note that unused moisture sensitive parts need to be resealed in the moisture barrier bag. If the reels exceed the exposure
limit and need to be rebaked, most carrier tape and shipping reels are not rated as bakeable at 125°C. If baking is required,
devices may be baked according to section 4, table 4-1, column 8 of Joint Industry Standard IPC/JEDEC J-STD-033.
Table 1 provides useful information for carrier tape and reels used for shipping the devices described in this document.
Table 1. Tape and Reel
Rev A13 DS080409
Figure 1. Carrier Tape Drawing with Part Orientation
RFMD Part Number
Notes:
Sprocket holes toward
rear of reel
1. All dimensions are in millimeters (mm).
2. Unless otherwise specified, all dimension tolerances per EIA-481.
3. 10 sprocket hole pitch cumulative tolerance ±.02.
NBB-300
7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical
support, contact RFMD at ([phone] or [e-mail].
Bo 3.1±.1
Inch (mm)
Diameter
7 (178)
1.3±.1
Reel
Location
Tape and Reel Dimensions
Pin 1
1.3±.1
3.1±.1
All Dimensions in Millimeters
Direction of Feed
15 inch Trailer
Inch (mm)
Diameter
2.4 (61)
See Note 3
2.00±.05
Hub
Ao
4.0
Width
(mm)
Top View
P
12
15 inch Leader
Pocket Pitch
Bo = 6.1 ±.1
F = 5.50 ±.05
Ko = 2.0 ±.1
P = 8.0 ±.1
Ao = 5.8 ±.1
W = 12.0 ±.3
Ø1.5 +.1
(mm)
8
.0
F
1.75
W
Single
Feed
NBB-300
Ko
Units per
Reel
1000
0.30±.05
7 of 10