ACPM-7833-TR1 Avago Technologies US Inc., ACPM-7833-TR1 Datasheet - Page 9

• Manufacturer Part Number: ACPM-7833-TR1
• Description: IC PA MOD CDMA1900 PCS 8-SMD
• Manufacturer: Avago Technologies US Inc.
• Type: Power Amplifierr

Specifications of ACPM-7833-TR1

• Current - Supply: 520mA
• Frequency: 1.85GHz ~ 1.91GHz
• Gain: 27.5dB
• Noise Figure: 4.5dB
• Package / Case: 10-SMD Module
• Rf Type: CDMA
• Voltage - Supply: 3.2V ~ 4.2V
• Operating Frequency: 1910 MHz
• Supply Current: 550 mA
• Maximum Power Dissipation: 2500 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 30 C
• Number Of Channels: 1 Channel
• Frequency (max): 1.91GHz
• Power Supply Requirement: Single
• Single Supply Voltage (min): 3.2V
• Single Supply Voltage (typ): 3.3V
• Single Supply Voltage (max): 4.2V
• Package Type: SMT
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temperature Classification: Commercial
• Operating Temp Range: -30C to 85C
• Pin Count: 10
• Mounting: Surface Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• P1db: -
• Test Frequency: -
• Lead Free Status / Rohs Status: Compliant

cdma 2000 1xRTT Characterization
System Description
CDMA2000 is the TIA’s standard for third generation
(3G) technology and is an evolution of the IS-95 CDMA
format. CDMA2000 includes 1X RTT in the single-carrier
mode and 3X RTT in the multi-carrier mode. This paper
describes the CDMA2000 1X RTT approach and its
performance with Avago Technologies 4x4 CDMA PAs,
ACPM-7833. CDMA2000 1X RTT, being an extension of
the IS-95 standard, has a chip rate of 1.2288Mchip/s.
However, in 1xRTT, the reverse link transmits more than
one code channel to accommodate the high data rates.
The minimum configuration consists of a reverse pilot
Table 1. Transmitter Specification in Reverse Link.
Specification
ERP at Maximum Output Power
Minimum Controlled Output Power
Waveform Quality Factor and Frequency Accuracy
Typical channel configurations below are based on the transmitter test
1) “Basic” Voice only configuration
2) Voice and Data configuration
3) Voice and Control configuration
4) Control channel only configuration
9
Spurious Emission at
Maximum RF output
power offset frequency
within the range
condition in the reverse link.
– R-PICH @ -5.3 dB
– R-FCH @ -1.5 dB 9.6 kbps
– R-PICH @ -5.3 dB
– R-FCH @ -4.54 dB 9.6 kbps
– R-SCH1 @ -4.54 dB 9.6 kbps
– R-PICH @ -5.3 dB
– R-FCH @ -3.85 dB 9.6 kbps
– R-DCCH @ -3.85 dB 9.6 kbps
– R-PICH @ -5.3 dB
– R-DCCH @ -1.5 dB 9.6 kbps
885 kHz to 1.98 MHz
Less stringent of -42 dBc/30 kHz
or -54 dBm/1.23 MHz
1.98 MHz to 3.125 MHz
Less stringent of -54 dBc/30 kHz
or -54 dBm/1.23 MHz
3.125 MHz to 5.625 MHz
-13 dBm/100 kHz
SR1, Band Class 0(Cellular band)
(R-Pilot) channel for synchronous detection by the Base
Transceiver System (BTS) and a reverse fundamental
channel (R-FCH) for voice. Additional channels such as
the reverse supplemental channels (R-SCHs) and the
reverse dedicated channel (R-DCCH) are used to send
data or signaling information. Channels can exist at
different rates and power levels.
Table 1 shows the transmitter specification in
CDMA2000 reverse link.
Spread Rate1
Lower limit +23 dBm
Upper limit +30 dBm
-50 dBm/1.23 MHz
>0.944
1.25 MHz to 1.98 MHz
Less stringent of -42 dBc/30 kHz
or -54 dBm/1.23 MHz
Less stringent of -50 dBc/30 kHz
or -54 dBm/1.23 MHz
2.25 MHz to 6.25 MHz
-13 dBm/1 MHz
1.98 MHz to 2.25 MHz
SR1, Band Class1(PCS band)