1002-TCB1D434 Silicon Laboratories Inc, 1002-TCB1D434 Datasheet - Page 2

• Manufacturer Part Number: 1002-TCB1D434
• Description: BOARD EVALUATION FOR SI1002
• Manufacturer: Silicon Laboratories Inc
• Type: Transceiver, ISMr

Specifications of 1002-TCB1D434

• Mfg Application Notes: SI1000 Code Examples AppNote
• Frequency: 434MHz
• Supply Voltage (min): 0.9 V
• Product: RF Modules
• Maximum Frequency: 915 MHz
• Output Power: 13 dBm
• Antenna: SMA
• Supply Voltage (max): 3.6 V
• For Use With/related Products: Si100x
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 336-1891

Si10xx-DK
3. Software Overview
All software required to develop firmware and communicate with the target microcontroller is included in the CD-
ROM. The CD-ROM also includes other useful software.
Below is the software necessary for firmware development and communication with the target microcontroller:


Other useful software that is provided in the CD-ROM includes the following:



3.1. Software Installation
The included CD-ROM contains the Silicon Laboratories Integrated Development Environment (IDE), Keil software
8051 tools and additional documentation. Insert the CD-ROM into your PC’s CD-ROM drive. An installer will
automatically launch allowing you to install the IDE software or read documentation by clicking buttons on the
Installation Panel. If the installer does not automatically start when you insert the CD-ROM, run autorun.exe found
in the root directory of the CD-ROM. Refer to the ReleaseNotes.txt file on the CD-ROM for the latest information
regarding known problems and restrictions. After installing the software, see the following sections for information
regarding the software and running one of the demo applications.
3.2. CP210x USB to UART VCP Driver Installation
The Si10xx Target Board includes a Silicon Laboratories CP2103 USB-to-UART Bridge Controller. Device drivers
for the CP2103 need to be installed before PC software such as HyperTerminal can communicate with the target
board over the USB connection. If the "Install CP210x Drivers" option was selected during installation, this will
launch a driver “unpacker” utility.
1. Follow the steps to copy the driver files to the desired location. The default directory is C:\SiLabs\MCU\CP210x.
2. The final window will give an option to install the driver on the target system. Select the “Launch the CP210x
3. If selected, the driver installer will now launch, providing an option to specify the driver installation location. After
4. If the “Launch the CP210x VCP Driver Installer” option was not selected in step 3, the installer can be found in
5. To complete the installation process, connect the included USB cable between the host computer and the USB
6. If needed, the driver files can be uninstalled by selecting “Silicon Laboratories CP210x USB to UART Bridge
3.3. Silicon Laboratories IDE
The Silicon Laboratories IDE integrates a source-code editor, a source-level debugger, and an in-system Flash
programmer. See Section 5. "Using the Keil Software 8051 Tools with the Silicon Laboratories IDE‚" on page 8 for
detailed information on how to use the IDE. The Keil Evaluation Toolset includes a compiler, linker, and assembler
and easily integrates into the IDE. The use of third-party compilers and assemblers is also supported.
3.3.1. IDE System Requirements
The Silicon Laboratories IDE requirements:



2
Silicon Laboratories Integrated Development Environment (IDE)
Keil 8051 Development Tools (macro assembler, linker, evaluation C compiler)
Configuration Wizard 2
Keil µVision Drivers
CP210x USB to UART Virtual COM Port (VCP) Drivers
VCP Driver Installer” option if you are ready to install the driver.
pressing the “Install” button, the installer will search your system for copies of previously installed CP210x
Virtual COM Port drivers. It will let you know when your system is up to date. The driver files included in this
installation have been certified by Microsoft.
the location specified in step 2, by default C:\SiLabs\MCU\CP210x\Windows_2K_XP_S2K3_Vista. At this
location run CP210xVCPInstaller.exe.
connector (P3) on the Si10xx Target Board. Windows will automatically finish the driver installation. Information
windows will pop up from the taskbar to show the installation progress.
(Driver Removal)” option in the “Add or Remove Programs” window.
Pentium-class host PC running Microsoft Windows 2000 or newer
One available USB port
64 MB RAM and 40 MB free HD space recommended
Rev. 0.1