D4DS-K3 Omron, D4DS-K3 Datasheet

Page 1

... F:Four mounting directions possible (Front-side mounting at shipping) Note: An order for the head part or the switch part alone cannot be accepted. (The Operation Key is sold separately.) http://www.ia.omron.com/ Operation Key D4DS- Operation Key Type 1:Horizontal mounting 2:Vertical mounting 3:Adjustable mounting (Horizontal) 5:Adjustable mounting (Horizontal/Vertical) (c)Copyright OMRON Corporation 2008 All Rights Reserved ...

Page 2

... G1/2 1NC/1NO M20, includes M20-to-1/2-14NPT conversion adapter M20 Pg13.5 G1/2 2NC/1NO M20, includes M20-to-1/2-14NPT conversion adapter M20 1NC/1NO 2NC M12 connector 1NC/1NO (c)Copyright OMRON Corporation 2008 All Rights Reserved. D4NS Model D4NS-1AF * D4NS-2AF * D4NS-3AF D4NS-4AF D4NS-1BF * D4NS-2BF * D4NS-3BF D4NS-4BF D4NS-1CF * D4NS-2CF * ...

Page 3

... EN60947-5-1 *1. Certification for CSA C22.2 No authorized by the UL mark. *2. Only certain models have been certified. http://www.ia.omron.com/ Model D4DS-K1 D4DS-K2 D4DS-K3 D4DS-K5 Certified Standard Ratings TÜV (EN60947-5-1), CCC (GB14048.5) Item Rated operating current (I Rated operating voltage (U Note: Use fuse type that conforms to IEC60269 as a short-circuit protection device ...

Page 4

... VDC (N-level reference value) 300 V 50/60 Hz Class II (double insulation) 3 (EN60947-5-1) 2 100 M min min Hz, 0.75 mm single amplitude 2 1,000 m/s min. 2 300 m/s min. 100 A (EN60947-5- (EN60947-5- (with no icing) 95% max. Approx (D4NS-1CF) (c)Copyright OMRON Corporation 2008 All Rights Reserved. D4NS 4 ...

Page 5

... Zb 21- 33- Stroke Operation Key insertion 33 34 completion position (c)Copyright OMRON Corporation 2008 All Rights Reserved. D4NS Terminal 12 Terminal 22 Terminal 32 (34) Remarks Only NC contacts 11-12 have a ON certified direct opening mechanism. Extraction completion The terminals 11-12 and 33-34 position can be used as unlike poles. ...

Page 6

... Two, 4 dia. holes 0 depth: 5 2.15±0.05R mounting holes M12 × 14.2 ± 0 (c)Copyright OMRON Corporation 2008 All Rights Reserved. D4NS (Unit: mm) Model D4NS-1@F D4NS-2@F Operating D4NS-3@F characteristics D4NS-4@F Key insertion force 15 N max. Key extraction force 30 N max. Pretravel (PT) 6± ...

Page 7

... Operation Keys D4DS- Four, 2.15R D4DS-K2 10 Note: Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. http://www.ia.omron.com D4DS- Black 2 6.3 D4DS-K5 20 Four, 2.15R Black (c)Copyright OMRON Corporation 2008 All Rights Reserved. D4NS Angle adjustment screw 20° 9 dia. 4.5 dia. 8 dia. ...

Page 8

... Permissible difference in center lines between the Operation Key and key hole is ±1. Vertical key insertion radius R ≥ 200 (33.5) D4NS-1@F + D4DS-K2 (with Top-inserted Operation Key) Horizontal key insertion radius R ≥ 200 Vertical key insertion radius R ≥ 200 (33.5) (c)Copyright OMRON Corporation 2008 All Rights Reserved. ...

Page 9

... Key insertion face Permissible difference in center lines between the Operation Key and key hole is ±1. Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. http://www.ia.omron.com/ D4NS-1@F + D4DS-K3 (with Top-inserted Operation Key) Horizontal key insertion radius R ≥ 50 (40 ±0.15 ) ...

Page 10

... Switch Mounting Holes and Studs Operation Key Mounting Holes 1-Conduit Modules Horizontal/Vertical Mounting (D4DS-K1/-K2) Two, M4 2.5 ±0.1 20 ±0.1 22 ±0.1 47 ±0.1 Horizontal Adjustable Mounting (D4DS-K3) 22 -0.05 ±0.1 4 dia. -0.15 Height: 4.8 max. Horizontal/Vertical Adjustable 2-Conduit Modules Mounting (D4DS-K5) Two, M4 2.5 ±0.1 5.35 ± ...

Page 11

... JPK-16, GP-13.5, or GPM20) and tighten with proper tightening torque. LAPP is a German manufacturer. Before using a 2-conduit type 1/2-14NPT connector, attach the enclosed adapter to the Switch, and used the above connector. (c)Copyright OMRON Corporation 2008 All Rights Reserved. D4NS-@CF (2NC/1NO) D4NS-@FF (2NC/1NO (MBB ...

Page 12

... D4DS-1AFS D4NS-1BF D4DS-2AFS D4NS-2BF D4DS-3AFS D4NS-3BF D4DS-5AFS D4NS-5BF D4DS-6AFS D4NS-6BF Operation Key D4DS-K1 D4DS-K2 D4DS-K3 D4DS-K5 All of the above Operation Keys can be used with the D4NS. Recommended Substitute Product (1-Conduit D4NS) Head cap 7.5 30.6 30.2 15.5 15.3 4.4 41 33.5 2.5 20 ± ...

Page 13

... Injury may result. Do not drop the Switch. Doing so may prevent the Switch from functioning to its full capability. Do not under any circumstances disassemble or modify the Switch. Doing so may cause malfunction. (c)Copyright OMRON Corporation 2008 All Rights Reserved. C-1 ...

Page 14

... Key may damage the Switch or affect machine safety. Do not operate the Switch with anything other than the special OMRON Operation Key, otherwise the Switch may break or the safety of the system may not be maintained. Do not impose excessive force on the Operation Key while the Key is inserted into the Switch or drop the Switch with the Operation Key inserted ...

Page 15

... Do not impose shock or vibration on the Actuator while it is fully pressed. Otherwise, the Actuator will partially abrade and an actuation failure may result. t (c)Copyright OMRON Corporation 2008 All Rights Reserved. C-3 ...

Page 16

... Switch. When complying with EN certified ratings, use a 10-A IEC 60269- compliant fuse. (c)Copyright OMRON Corporation 2008 All Rights Reserved. Precautions for All Switches Incorrect Power Connection Example ...

Page 17

... Unusable range 0.1 (c)Copyright OMRON Corporation 2008 All Rights Reserved. Precautions for All Switches when it 3 Element selection Use the following as guides for C and R values 0.5 F per contact current ( per contact voltage (V) These values depend on various factors, including the load ...

Page 18

... When storing the Switch, make sure that the location is free of corrosive gas, such as H does not have a high temperature or humidity. Be sure to inspect the Switch before use if it has been stored for three months or more. (c)Copyright OMRON Corporation 2008 All Rights Reserved. Precautions for All Switches ), ammonium gas (NH ), nitric gas (HNO high temperature and humidity ...

Page 19

... Contact welding due to an incorrectly connected power source. Foreign materials or oil penetrated into the contact area. (c)Copyright OMRON Corporation 2008 All Rights Reserved. Precautions for All Switches Remedy Change the design of the dog or cam and smooth the contacting surface of the cam. ...

Page 20

... Terminal screw screw Terminal Terminal Incorrect Wiring Incorrect Crimped location facing down Lead Crimp terminal Terminal Terminal screw screw Terminal Terminal Too close to maintain dielectric strength http://www.ia.omron.com/ Correct (c)Copyright OMRON Corporation 2008 All Rights Reserved. Precautions for All Switches C-8 ...

Page 21

... When transferring devices and equipment, be sure to keep one copy of the Operating Manual and pack another copy with the device or equipment so the person receiving it will have no problem operating it. • Related International Standards: ISO 12100 Basic Concepts, General Principles for Design IEC 61508 Functional Safety of Electrical/Electronic/Programmable Electronic Safety-related Systems http://www.ia.omron.com/ WARNING (c)Copyright OMRON Corporation 2008 All Rights Reserved. ...

Page 22

... Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specifi ed) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS ...